LiftMaster 883LMW Instructions - English French Spanish - Page 1
LiftMaster 883LMW Manual
View all LiftMaster 883LMW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Connect Your Garage Door Opener to Your Home Wi-Fi® Network (for Wi-Fi garage door openers ONLY) PUSH BUTTON DOOR CONTROL Model 883LMW For use with Security+ 2.0® Garage Door Openers. All Security+ 2.0® Garage Door Openers have a yellow Learn button and a yellow antenna wire. 1 Press and hold the light button (located on the right side of the door control button) for 6 seconds until the LED under the front button begins to blink. You have 20 minutes to complete the connection process. 2 On your mobile device, go to Settings > Wi-Fi and select the network with the "MyQ-" prefix. 3 Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com into the browser address bar. Follow the on screen prompts to connect the garage door opener to your Wi-Fi network. The MyQ serial number will display on screen. Write the serial number in the space below. Push Button Light Button 4 Download the MyQ app from the App Store® or Google Play™ store. Sign up for your MyQ account and add the MyQ serial number to your account. Push Button Door Control 883LMW To add a second Wi-Fi garage door opener, repeat steps 1-3. Add the second MyQ serial number to your account in the MyQ app. To prevent possible SERIOUS INJURY or DEATH from electrocution: If you are unsuccessful adding your device, try an alternate web browser or visit WiFiHelp.LiftMaster.com. Installation Programming • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 12 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a 1 Unplug the garage door opener. 2 Strip 1/4" (6 mm) of insulation from one end of the wire and separate the wires. 6 Strip 7/16" (11 mm) of insulation from the other end of the wire near the garage door opener. 7 Connect the wire to the red and white terminals on TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE DOOR CONTROL closing garage door: • Install door control within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door. • NEVER permit children to operate or play with door control 3 Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw. 4 Mount the door control with the hardware the garage door opener. 8 Reconnect power to the garage door opener. The LED behind the Push button on the door control will blink if installed correctly. 1 Press and hold the Light button and the Push button until the Push button LED begins to blink. Push Button Light Button push buttons or remote control transmitters. provided. 9 To synchronize the door control to the garage door • Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door. NOTICE: This device complies with part 15 of the FCC rules and Industry Canada's licence- 5 Run the white and red/white wire from the door control to the garage door opener. Attach the wire to the wall and ceiling with the staples (if applicable). opener, press the push button until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push button, each press of the push button will activate the garage door opener. 7 6 7/16" (11 mm) 2a Press the button on the remote control that you wish to operate your garage door. Push Button Door Control 883LMW 1 4GHI 7PRS * E RED WHITE WHITE GREY exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device has been tested and found to comply with the limits for a Class B digital device, To insert or release wire, push in tab with screwdriver tip. OR pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver 5 2b Enter a 4-digit ?? ?? personal identification Do not pierce the wire with the staple as this may cause a short or an number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. The garage door opener lights will flash (or two clicks will PIN 4GHI 5JKL 6MNO 7PRS 1 2ABC 3DEF 4GHI 5JKL 6MNO 7PRS 8TUV 9WXY * * 0 QZ # ENTER 8TUV 0 QZ 9WXY # is connected. open circuit. be heard) when the code has ENTER - Consult the dealer or an experienced radio/TV technician for help. been programmed. CAN ICES-3 (B)/NMB-3 (B) WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov 1/4" (6 mm) PRE-WIRED INSTALLATIONS: Choose any two wires to connect, but make note of which wires 2 are used so that the correct wires are connected to the garage door opener. 3 4