LiftMaster CSL24VDC CSL24VDC Gate Operator and Accessory Site Plan Manual - Page 2

Vehicular Slide Gate Operator - model

Page 2 highlights

Commercial DC VEHICULAR SLIDE GATE OPERATOR Model CSL24VDC TYPICAL INSTALLATION NOTE: One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists at either the opening or closing direction. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving. Any gap between the gate and a fixed object such as a wall, pillar, column or the operator itself larger than 2 1/4 inches must be filled. SINGLE GATE Warning Sign Wire Gauge 14 12 10 8 6 4 OPERATOR POWER SOURCE 120 Vac 130 feet 240 Vac 260 feet 205 feet 325 feet 410 feet 650 feet 520 feet 1040 feet 825 feet 1650 feet 1312 feet 2624 feet NOTE: Use copper conductors ONLY. Safety Catch Roller Edge Sensor Edge Sensor Photoelectric Sensors Operator DUAL GATE Earth Ground Rod Check national and local codes for proper depth Water Tight Conduit (Not provided) NOTE: Power and control wiring MUST be run in separate conduits. Warning Sign Safety Catch Roller Edge Sensor Edge Sensor Photoelectric Sensors Earth Ground Rod Check national and local codes for proper depth © 2014 LiftMaster All Rights Reserved 845 Larch Ave., Elmhurst, IL 60126 LiftMaster.com 01-37414B Operator NOTE: Wired connection in a dual gate setup is optional. Operators can be setup for wireless dual gate communication. Water Tight Conduit (Not provided) NOTE: Power and control wiring MUST be run in separate conduits. INSTALLATION DIMENSIONS OPERATOR DIMENSIONS 20" 21.1" Installation Blueprint DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR 4"(10 cm) 26" (66 cm) 14.6" 24" (61 cm) 4 Concrete Anchors 1/2" x 3 1/2" 24" (61 cm) CONCRETE PAD AND OPERATOR ATTACHMENT 5-5/8" 1/2" 2-1/4" 1-3/8" 6" Above Ground Below the frost line. Check all national and local codes. CONDUIT LOCATION (Gate) 7" 1-1/4" 3-1/2" min. 1-2" 2-3/4" MOUNTING FOOTPRINT 11.9" 10.3" 2.85" (Conduit) .63" 13" 23" 26" 10.4" 14.1" 8" 26" (66 cm) 4-1/2" 15" (Pad) 24" 14.6" SAFETY LAYOUT Sensors for Open Cycle Monitored Photoelectric Sensors ! ProIpnesridtye PrOopuetsritdye ProOpuetrstiyde PropInesritdye Sensors for Close Cycle

  • 1
  • 2

Commercial DC
VEHICULAR SLIDE GATE OPERATOR
Model CSL24VDC
Installation Blueprint
TYPICAL INSTALLATION
OPERATOR POWER SOURCE
Wire Gauge
120 Vac
240 Vac
14
130 feet
260 feet
12
205 feet
410 feet
10
325 feet
650 feet
8
520 feet
1040 feet
6
825 feet
1650 feet
4
1312 feet
2624 feet
SAFETY LAYOUT
INSTALLATION DIMENSIONS
© 2014 LiftMaster All Rights Reserved
845 Larch Ave., Elmhurst, IL 60126
LiftMaster.com
01-37414B
Inside
Property
Outside
Property
Outside
Property
Inside
Property
!
Monitored Photoelectric Sensors
Sensors for Open Cycle
Sensors for Close Cycle
14.6"
20"
21.1"
DUAL GATE
Operator
Water Tight
Conduit
(Not provided)
NOTE:
Power and control wiring
MUST be run in separate conduits.
Earth Ground Rod
Check national and local
codes for proper depth
Warning Sign
Photoelectric
Sensors
Safety Catch Roller
Operator
Photoelectric
Sensors
Safety Catch Roller
Edge Sensor
Edge Sensor
Edge
Sensor
Edge Sensor
SINGLE GATE
NOTE:
Use copper conductors ONLY.
Water Tight Conduit
(Not provided)
NOTE:
Power and control wiring
MUST be run in separate conduits.
Warning Sign
Earth Ground Rod
Check national and local
codes for proper depth
OPERATOR DIMENSIONS
DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR
CONCRETE PAD AND OPERATOR ATTACHMENT
4"(10 cm)
24" (61 cm)
26"
(66 cm)
4 Concrete
Anchors
1/2" x 3 1/2"
Below the frost line.
Check all national
and local codes.
6" Above Ground
26"
(66 cm)
24"
(61 cm)
14.6"
MOUNTING FOOTPRINT
11.9"
.63"
CONDUIT LOCATION
10.3"
2.85"
10.4"
14.1"
26"
24"
15"
23"
8"
13"
1-3/8"
1-2" 2-3/4"
3-1/2" min.
5-5/8"
1/2"
4-1/2"
7"
1-1/4"
(Gate)
2-1/4"
(Conduit)
(Pad)
NOTE:
One or more non-contact sensors shall be located where the risk
of entrapment or obstruction exists at either the opening or closing
direction. Care shall be exercised to reduce the risk of nuisance tripping,
such as when a vehicle, trips the sensor while the gate is still moving.
Any gap between the gate and a fixed object such as a wall, pillar,
column or the operator itself larger than 2 1/4 inches must be filled.
NOTE:
Wired connection in
a dual gate setup is optional.
Operators can be setup for wireless
dual gate communication.