LiftMaster H GT- Logic 4 User Manual - Page 11
Accessories
View all LiftMaster H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
OPEN ACCESSORIES OPEN CLOSE OPEN REMOTEOPENCONTROLS 315MHz CLOSE 371LM 1-Button SECURITY✚® Remote Control: Includes visor clip. OPEN CLOSE 373LM 3-Button SECURITY✚® Remote Control: Includes visor clip. 333LM OPEN 3-Button Tri-Colored Dip Switch Remote Control: Includes visor clip. OPEN CLOSE CONTROL STATIONS 02-101 1-Button Control Station: OPEN Steel enclosure. OPEN 02-102 2-Button Control Station: OPEN Steel enclosure. CLOSE 02-103L 02-110 3-Button Control Station: OPEN CLOSE Steel enclosure with Maintenance Alert System. STOP Key Control Station: OPEN CLOSE Indoor flush mount, NEMA 1 with Stop button. STOP MOUNTING BRACKETS ENTRAPMENT PROTECTION DEVICES MONITORED CPS-UN4 Commercial Protector System®: Provides protection on doors up to 45' wide. NEMA-4 rated. CPS-U CPS3 CPS-EI CPS-EI E1 LMEP2 E2 LMEP1 E3 E4 40-34141-1 65ME1234 65ME110 65-8202 65-5202 OPEN Commercial Protector System®: CLOSE Provides protection on doors up to 30' wide. Option Logic Board: For use when more than one set of photoelectric eyes are required. Monitored Safety Edge Interface: For use with the approved 4-wire safety edge (see beloOPwEN ). CLOSE Miller ME123 4-Wire Monitored Safety Edge: For sectional or rolling doors. OPEN Miller ME110 4-Wire Monitored Safety Edge: CLOSE For rolling grilles and counter shutters. NON-MONITORED Vehicle Detection System: Pneumatic Sensing Edge Kit with exterior air switch, 2-wire coil cord and 14' air hose. Vehicle Detection System: Pneumatic Sensing Edge Kit with exterior air switch, 2-wire take-up reel (20' extended) and 14' air hose. 10-12360 08-9098 08-9098EZ 1A4324 1A4324EZ Heavy gauge steel bracket for vertical or horizontal mount on either front or top of coil on a rolling door. Has a variety of mounting hole patterns compatible with many OEM manufacturers. May be welded. For use with J, H, DJ, and DH operators. Cast iron bracket to mount J, H, DH, DJ, and GH side mount operators on end bracket of a rolling door or grill. For vertical or horizontal mount on either front or top of coil. Same as 08-9098, but with adapter plate to hold mounting OPEN bolt holes in place for ease of use. CLOSE Heavy gauge steel bracket for vertical or horizontal mount on either front or top of coil on a rolling door. May be welded. For use with J, H, DJ, and DH operators. Same as 1A4324, but with adapter plate to hold mounting bolt holes in place for ease of use. TLSCARD Timer Light Status Card: The TLS option card provides special functionality to activate and flash auxiliary devices such as lights, bells, and horns/strobes at various door positions, and to provide special timer functions. AUXCARD Auxiliary Contact Card: The Auxiliary Contact option card has both Normally-Open and Normally-Closed contacts that actuate when the door is idle, opening, or closing. MOUNTING CHANNELS OPEN 65ME123C CLOSE U-Shaped Mounting Channel: For 65ME1234 edge when installed on sectional doors. 65ME123C1 OPEN CLOSE T-ShapeOdPENMounting Channel: For 65MCELOS1E 234 edge when installed on rolling doors. Fits between L-shaped angles used to construct a bottom bar on rolling doors. MISCELLANEOUS 1A3982 Operator Cover: For use with wall-mounted J, H, GH, DH or DJ operators. Measures 31" x 19" x 18" (L x W x D). Assembly required. Recommended for damp environments where direct spray is present. Required when the operator is installed less than 8 feet above the floor. 86LM (15') 86LMT (25') Antenna Extension Kit: The antenna extension kit can be used with EXT-ANT for maximum radio receiver range. 65ME123CA3 L-Shaped Mounting Channel: For 65ME1234 edge when installed on sectional doors. OPEN CLOSE CHAIN TENSIONERS For Jackshaft Type Operators 71-6023 For 1" shafts. Recommended to properly tension drive chain between operator shaft and door shaft. 71-6125 Same as 71-6023, but for 1-1/4" shafts. 11