LiftMaster MJ MGJ User's Guide Manual - Page 7

Warning - manual

Get LiftMaster MJ PDF manuals and user guides View all LiftMaster MJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

WARNING TESTING WARNING CAUTION Turn on power, LED will flash 7 times on power up. Test all controls and safety devices to make sure they are working properly. If the operator does not function properly, contact your installing dealer. IMPORTANT NOTES: • Do not leave power to the operator on unless all safety and entrapment protection devices have been tested and are working properly. • Be sure you have read and understand all safety instructions included in this manual. • Be sure the owner or person(s) responsible for operation of the door have read and understand the safety instructions, know how to electrically operate the door in a safe manner and how to manually disconnect the door from the operator. TAESVT E3-BRUTTTIOSNSCOENMTROELNSTTATION 1. Press OPEN button. (The door should move in the open direction.) ATTENTION 2. Press STOP button. (The door should stop.) 3. Press CLOSE button. (The door should move in the close direction.) 4. Release CLOSE button. Door should stop if in C2 mode. (The door should continue closing if in B2 mode.) 5. Press STOP button. (The door should stop.) TEST LIMIT ADJUSTMENT 1. Press OPEN button. (The door should open.) 2. Allow the door to fully open. 3. Press CLOSE button. (The door should close.) 4. Allow the door to fully close. 5. If the limits are not set properly, contact your installing dealer. WARNING To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric power BEFORE performing ANY maintenance. TEST THE SAFETY DEVICES (IF INSTALLED) 1. Open the door. 2. Place an obstruction in the path of the photo eyes or sensing edge. 3. Press the CLOSE button. The door should not close if photo eyes are installed. The door AVERTISSEMENT should close to obstruction and reverse if sensing edge is installed. 4. Remove the obstruction. 5. Press CLOSE button. Door should close. AVERTISSEMENT If door did not reverse from obstruction, check safety devices. TEST REMOTE CONTROL * Requires B2 wiring type and compatible LiftMaster remote control. In C2 wiring the remote control will open the door only. 1. Press remote control button. 2. Door should open. Allow the door to fully open. 3. Press remote control button. 4. Door should close. Allow door to fully close. ADVERTENCIA PRECAUCIÓN ADVERTENCIA ADVERTENCIA 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Turn on power, LED will flash 7 times on power up. Test all
controls and safety devices to make sure they are working
properly. If the operator does not function properly, contact your
installing dealer.
IMPORTANT NOTES:
•
Do not leave power to the operator on unless all safety and
entrapment protection devices have been tested and are working
properly.
•
Be sure you have read and understand all safety instructions
included in this manual.
•
Be sure the owner or person(s) responsible for operation of the
door have read and understand the safety instructions, know how
to electrically operate the door in a safe manner and how to
manually disconnect the door from the operator.
To avoid SERIOUS PERSONAL INJURY or DEATH from
electrocution, disconnect ALL electric power BEFORE performing
ANY maintenance.
WARNING
WARNING
TEST 3-BUTTON CONTROL STATION
1.
Press OPEN button. (The door should move in the open
direction.)
2.
Press STOP button. (The door should stop.)
3.
Press CLOSE button. (The door should move in the close
direction.)
4.
Release CLOSE button. Door should stop if in C2 mode. (The
door should continue closing if in B2 mode.)
5.
Press STOP button. (The door should stop.)
TEST LIMIT ADJUSTMENT
1.
Press OPEN button. (The door should open.)
2.
Allow the door to fully open.
3.
Press CLOSE button. (The door should close.)
4.
Allow the door to fully close.
5.
If the limits are not set properly, contact your installing dealer.
TEST THE SAFETY DEVICES (IF INSTALLED)
1.
Open the door.
2.
Place an obstruction in the path of the photo eyes or sensing
edge.
3.
Press the CLOSE button.
The door should not close if photo eyes are installed. The door
should close to obstruction and reverse if sensing edge is
installed.
4.
Remove the obstruction.
5.
Press CLOSE button. Door should close.
If door did not reverse from obstruction, check safety devices.
TEST REMOTE CONTROL
*
Requires B2 wiring type and compatible LiftMaster remote
control. In C2 wiring the remote control will open the
door only.
1.
Press remote control button.
2.
Door should open. Allow the door to fully open.
3.
Press remote control button.
4.
Door should close. Allow door to fully close.
TESTING
7