LiftMaster TriCode Systems Coding Instructions - Page 2

Step 2: Set Transmitter Configuration Switchs

Get LiftMaster TriCode Systems PDF manuals and user guides View all LiftMaster TriCode Systems manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

STEP 2: SET TRANSMITTER CONFIGURATION SWITCH(S) The TriCode™ Transmitter is factory set to Linear/Delta-3™ position. Using a pointed object set transmitter configuration switches to desired setting.. STEP 3: SET TRANSMITTER DIP SWITCH(S) The TriCode™ Transmitter DIP switch(s) are factory set, CH1 OFF (1-10) and CH2 ON (110). Using a pointed object set transmitter DIP switches to desired setting. For Linear/Delta-3™ compatibility, set codes on switches 1 through 8. Switches 9 and 10 are not used for Linear/Delta-3™ products. Note: Switches in receiver must match the switches in all transmitters used to operate the receiver. Some older radios use toggle switches and it may be difficult to determine 'ON' & 'OFF'. If so, try reverse settings on the TriCode™. STEP 4: RECODE RECEIVER CODES Once the transmitter codes have been set, verify the receiver codes are set to the following settings: Linear/Delta-3™ Receiver Type Detail When the TC4 is set to the Linear/Delta-3™ transmitter type, set the receiver DIP switches as follows. Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1. Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from Button 2. Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from Button 3. Receiver 4 - Set switch 1 Off, switch 2 ON, match switches 3-8 on switch 2, activates from Button 4. Multi-Code™ Receiver Type Detail When the TC4 is set to the Multi-Code™ transmitter type, set the receiver DIP switches as follows. Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1. Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2. Receiver 3 - Set switch 10 OFF. match switches 1-9 on switch 2, activates from Button 3.

  • 1
  • 2
  • 3
  • 4
STEP 2: SET TRANSMITTER CONFIGURATION SWITCH(S)
The TriCode™ Transmitter is factory set to Linear/Delta-3™ position. Using a pointed object
set transmitter configuration switches to desired setting..
STEP 3: SET TRANSMITTER DIP SWITCH(S)
The TriCode™ Transmitter DIP switch(s) are factory set, CH1 OFF (1-10) and CH2 ON (1-
10).
Using a pointed object set transmitter DIP switches to desired setting. For Linear/Delta-3™
compatibility, set codes on switches 1 through 8. Switches 9 and 10 are not used for
Linear/Delta-3™ products.
Note: Switches in receiver must match the switches in all transmitters used to
operate the receiver. Some older radios use toggle switches and it may be difficult
to determine 'ON' & 'OFF'. If so, try reverse settings on the TriCode™.
STEP 4: RECODE RECEIVER CODES
Once the transmitter codes have been set, verify the receiver codes are set to the following
settings:
Linear/Delta-3™ Receiver Type Detail
When the TC4 is set to the Linear/Delta-3™ transmitter type, set the receiver DIP switches
as follows.
Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1.
Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from
Button 2.
Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from
Button 3.
Receiver 4 - Set switch 1 Off, switch 2 ON, match switches 3-8 on switch 2, activates from
Button 4.
Multi-Code™ Receiver Type Detail
When the TC4 is set to the Multi-Code™ transmitter type, set the receiver DIP switches as
follows.
Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.
Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.
Receiver 3 - Set switch 10 OFF. match switches 1-9 on switch 2, activates from Button 3.