Linksys BEFW11S4 User Guide - Page 43

Keep Alive, Save Settings, Status, Connect, Manual, IP Address: 192.168.1.50 - manual setup

Get Linksys BEFW11S4 - Wireless-B Broadband Router Wireless PDF manuals and user guides
UPC - 745883549948
View all Linksys BEFW11S4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Wireless-B Broadband Router • If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf's instructions. • Set a static IP address on the PC; refer to "Problem #1, I need to set a static IP address." Use the following IP address settings for the computer you are using: IP Address: 192.168.1.50 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 • Perform the upgrade using the TFTP program or the Router's web-based utility through its System tab. 15. My DSL service's PPPoE is always disconnecting. PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet. • There is a setup option to "keep alive" the connection. This may not always work, so you may need to reestablish connection periodically. 1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router. 2. Enter the password, if asked. (The default password is admin.) 3. On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds). 4. Click the Save Settings button. 5. Click the Status tab, and click the Connect button. 6. You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected. • Click the Save Settingsy button to continue. • If the connection is lost again, follow steps 1- 6 to re-establish connection. 16. I can't access my e-mail, web or I am getting corrupted data from the Internet. The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500. For most DSL users, it is strongly recommended to use MTU 1492. • If you are having some difficulties, perform the following steps: 1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router. 2. Enter the password, if asked. (The default password is admin.) 3. Look for the MTU option, and select Manual. In the Size field, enter 1492. 4. Click the Save Settings button to continue. • If your difficulties continue, change the Size to different values. Try this list of values, one value at a time, in this order, until your problem is solved: 1462, 1400, 1362, 1300 Appendix A: Troubleshooting 37 Common Problems and Solutions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
37
Appendix A: Troubleshooting
Common Problems and Solutions
Wireless-B Broadband Router
•
If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open
the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s
instructions.
•
Set a static IP address on the PC; refer to “Problem #1, I need to set a static IP address.” Use the following
IP address settings for the computer you are using:
IP Address: 192.168.1.50
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
•
Perform the upgrade using the TFTP program or the Router’s web-based utility through its System tab.
15.My DSL service’s PPPoE is always disconnecting.
PPPoE is not actually a dedicated or always-on connection.
The DSL ISP can disconnect the service after a
period of inactivity, just like a normal phone dial-up connection to the Internet.
•
There is a setup option to “keep alive” the connection.
This may not always work, so you may need to re-
establish connection periodically.
1.
To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the
Router.
2.
Enter the password, if asked. (The default password is admin.)
3.
On the Setup screen, select the option
Keep Alive
, and set the Redial Period option at 20 (seconds).
4.
Click the
Save Settings
button.
5.
Click the
Status
tab, and click the
Connect
button.
6.
You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you
see the login status display as Connected.
•
Click the
Save Settingsy
button to continue.
•
If the connection is lost again, follow steps 1- 6 to re-establish connection.
16. I can’t access my e-mail, web or I am getting corrupted data from the Internet.
The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500.
For most DSL users, it is strongly recommended to use MTU 1492.
•
If you are having some difficulties, perform the following steps:
1.
To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the
Router.
2.
Enter the password, if asked. (The default password is admin.)
3.
Look for the MTU option, and select
Manual
. In the Size field, enter 1492.
4.
Click the
Save Settings
button to continue.
•
If your difficulties continue, change the Size to different values. Try this list of values, one value at a time,
in this order, until your problem is solved:
1462, 1400, 1362, 1300