Lowrance Broadband 3G Radar Installation Guide - Page 23

To start the radar, RI10 heading source selection, Dual Radar setup - 3g broadband digital radar

Get Lowrance Broadband 3G Radar PDF manuals and user guides View all Lowrance Broadband 3G Radar manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

To start the radar: From the radar screen select the Transmit button. RI10 heading source selection: The RI10 receives heading via SimNet or NMEA2000 network and transmits this data to the radar, where MARPA processing is performed. For Simrad installations with more than one SimNet heading source the RI10 will use the Simrad group source. The source used by the Simrad group can be viewed or changed via an NSE / NSO / NSS display in the Settings>Network>Sources... menu. Dual Radar setup: For B&G Zeus and Simrad NSO and NSE displays it is possible for two radars to be connected to the network and viewed simultaneously on one display. At time of installation radar source selection needs to be performed as described below. 1. Power up the system including both radars 2. On any display, the first radar ever detected by the display will be used as the source for all chart and radar panels. This source will be used by default for every system power-up thereafter, until changed The radar source is identified by radar type with a four digit number and is displayed in the top left corner of chart and radar panels:  Note: The four digit number is the last four digits of the radars serial number. 3. For a radar panel, the radar source can be changed in the Radar>Radar Options>Sources menu: 4. For a chart panel (with radar overlay on), the radar source can be changed in the Chart>Radar Options>Sources menu: 5. For pages with more than one radar or chart panel, it is possible to set up different radar sources for each panel Setup and Configuration | Broadband 3G/4G™ Radar Installation Guide | 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
|
21
Setup and Configuration
|
Broadband 3G/4G™ Radar Installation Guide
To start the radar:
From the radar screen select the Transmit button.
RI10 heading source selection:
The RI10 receives heading via SimNet or NMEA2000 network and transmits this data to the
radar, where MARPA processing is performed.
For Simrad installations with more than one SimNet heading source the RI10 will use the
Simrad group source. The source used by the Simrad group can be viewed or changed via an
NSE / NSO / NSS display in the Settings>Network>Sources… menu.
Dual Radar setup:
For B&G Zeus and Simrad NSO and NSE displays it is possible for two radars to be connected
to the network and viewed simultaneously on one display. At time of installation radar source
selection needs to be performed as described below.
1.
Power up the system including both radars
2.
On any display, the first radar ever detected by the display will be used as the source for all chart
and radar panels. This source will be used by default for every system power-up thereafter,
until changed
The radar source is identified by radar type with a four digit number and is displayed in the top
left corner of chart and radar panels:
Note:
The four digit number is the last four digits of the radars serial number.
3.
For a radar panel, the radar source can be changed in the Radar>Radar Options>Sources menu:
4.
For a chart panel (with radar overlay on), the radar source can be changed in the Chart>Radar
Options>Sources menu:
5.
For pages with more than one radar or chart panel, it is possible to set up different radar
sources for each panel