MSI MEG Z590 UNIFY User Manual - Page 43

V-Check Points Lite, T_SEN1: Thermal Sensor Connectors, JDASH1 : Tuning Controller connector

Get MSI MEG Z590 UNIFY PDF manuals and user guides View all MSI MEG Z590 UNIFY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

V-Check Points Lite These voltage checkpoints are used to measure the current system voltages. A multimeter (not included) will be required to check voltages. To measure voltage, place test leads on the GND (screw mounting hole) and a specific V-Check Point. Please refer to the manual of your multimeter for more information. GND VCCIO VCCSA DRAM VCORE VCCIO2 T_SEN1: Thermal Sensor Connectors This connector allows you to connect the thermistor cable and use it to monitor the temperature of the detection point. Sense GND Thermistor cable JDASH1 : Tuning Controller connector This connector is used to connect an optional Tuning Controller module. 2 14 1 13 1 No Pin 2 3 MCU_SMB_SCL_M 4 5 VCC5 6 7 PSIN#_R 8 9 OC_RETRY# 10 11 BLK+ 12 13 CLRCMOS_EN 14 NC MCU_SMB_SDA_M Ground FP_RST#_R OC_FS BLKNC Overview of Components 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
43
Overview of Components
JDASH1 : Tuning Controller connector
This connector is used to connect an optional Tuning Controller module.
1
2
14
13
1
No Pin
2
NC
3
MCU_SMB_SCL_M
4
MCU_SMB_SDA_M
5
VCC5
6
Ground
7
PSIN#_R
8
FP_RST#_R
9
OC_RETRY#
10
OC_FS
11
BLK+
12
BLK-
13
CLRCMOS_EN
14
NC
V-Check Points Lite
These voltage checkpoints are used to measure the current system voltages. A
multimeter (not included) will be required to check voltages. To measure voltage,
place test leads on the GND (screw mounting hole) and a specific V-Check Point.
Please refer to the manual of your multimeter for more information.
VCCIO
GND
VCCSA
DRAM
VCORE
VCCIO2
T_SEN1: Thermal Sensor Connectors
This connector allows you to connect the thermistor cable and use it to monitor the
temperature of the detection point.
Thermistor cable
GND
Sense