MSI Pro266TD User Manual - Page 64

ECP Mode Use DMA, Init Display First, OnChip USB Controller, USB Keyboard Support, IDE HDD Block

Get MSI Pro266TD PDF manuals and user guides View all MSI Pro266TD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Chapter 3 EPP or ECP+EPP mode. Settings: EPP1.7 and EPP1.9. ECP Mode Use DMA The item specifies the DMA channel 1 or 3 for the parallel port when it is set to ECP or ECP+EPP mode. Init Display First This item specifies which VGA card is your primary graphics adapter. Available settings: PCI Slot and AGP. OnChip USB Controller The item specifies which USB (Universal Serial Bus) Port is enabled. Settings: All Disabled, ALL Enabled, 2&3 USB Port, 1&2 USB Port, 1&3 USB Port, 3 USB Port, 2 USB Port, 1 USB Port. USB Keyboard Support Set to Enabled if your need to use an USB keyboard in the operating system that does not support or have any USB driver installed, such as DOS and SCO Unix. IDE HDD Block Mode This allows your hard disk controller to use the fast block mode to transfer data to and from the hard disk drive. Block mode is also called block transfer, multiple commands or multiple sector read/write. Enabled enables IDE controller to use block mode; Disabled allows the controller to use standard mode. PWRON After PWR-Fail This item specifies whether your system will reboot after a power failure or interrupt occurs. Available settins are: Off Leaves the computer in the power off state. On Reboots the computer. Former-Sts Restores the system to the previous status before power failure or interrupt occured. Power Status Led This item sets how the system uses Power LED on the case to indicate the 3-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Chapter 3
3-22
EPP
or
ECP+EPP
mode.
Settings:
EPP1.7
and
EPP1.9
.
ECP Mode Use DMA
The item specifies the DMA channel 1 or 3 for the parallel port when it
is set to
ECP
or
ECP+EPP
mode.
Init Display First
This item specifies which VGA card is your primary graphics adapter.
Available settings:
PCI Slot
and
AGP
.
OnChip USB Controller
The item specifies which USB (Universal Serial Bus) Port is enabled.
Settings:
All Disabled
,
ALL Enabled
,
2&3 USB Port
,
1&2 USB Port
,
1&3
USB Port
,
3 USB Port
,
2 USB Port
,
1 USB Port
.
USB Keyboard Support
Set to
Enabled
if your need to use an USB keyboard in the operating system
that does not support or have any USB driver installed, such as DOS and
SCO Unix.
IDE HDD Block Mode
This allows your hard disk controller to use the fast block mode to transfer
data to and from the hard disk drive.
Block mode is also called block
transfer, multiple commands or multiple sector read/write.
Enabled
enables
IDE controller to use block mode;
Disabled
allows the controller to use
standard mode.
PWRON After PWR-Fail
This item specifies whether your system will reboot after a power failure or
interrupt occurs.
Available settins are:
Off
Leaves the computer in the power off state.
On
Reboots the computer.
Former-Sts
Restores the system to the previous status before
power failure or interrupt occured.
Power Status Led
This item sets how the system uses Power LED on the case to indicate the