MSI Wind PC User Guide - Page 3

Safety Instructions - manual

Get MSI Wind PC - 0 MB RAM PDF manuals and user guides
UPC - 816909046847
View all MSI Wind PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Safety Instructions 1. Always read the safety instructions carefully. 2. Keep this user's manual for future reference. 3. Keep this equipment away from humidity. 4. Lay this equipment on a reliable flat surface before setting it up. 5. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS. 6. Check power adapter rating: 19V 3.42A, Max 65W . 7. Make sure the voltage of the power source and adjust properly 110-240V before connecting the equipment to the power inlet. Rating: 100-240V, 50- 60Hz, 1.7A. 8. Place the power cord such a way that people can not step on it. Do not place anything over the power cord. 9. Always unplug the power cord before inserting any add-on card or module. 10. All cautions and warnings on the equipment should be noted. 11. Never pour any liquid into the opening that could damage or cause electrical s h oc k . 12. If any of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well or you can not get it work according to user's manual. The equipment has dropped and damaged. The equipment has obvious sign of breakage. 13. DO NOTLEAVE THISEQUIPMENT INAN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 40o C (102oF), IT MAY DAMAGE THE EQUIPMENT. WARNING: 1. For every changes in power cord's usage, please use an approved power cord with condition greater or equal to H05VV-F, 3G, 0.75mm2. 2. Internal part is hazardous moving parts, please keep fingers and other body parts away. 3. For pluggable equipment, the socket-outlet shall be installed near the equip- ment and shall be easily accessible. 4. Do not disable the protective earth pin from the plug, the equipment must be connected to an earthed mains socket-outlet. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. For better environmental protection, waste batteries should be collected separately for recycling or special disposal. 1. The optical storage devices are classified as a Class 1 Laser products. Use of controls or adjustments or performance of procedures other than those specified. 2. Do not touch the lens inside the drive. iii

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
iii
Safety Instructions
1.
Always read the safety instructions carefully.
2.
Keep this user
’
s manual for future reference.
3.
Keep this equipment away from humidity.
4.
Lay this equipment on a reliable flat surface before setting it up.
5.
The openings on the enclosure are for air convection hence protects the
equipment from overheating. DO NOT COVER THE OPENINGS.
6.
Check power adapter rating: 19V
3.42A, Max 65W.
7.
Make sure the voltage of the power source and adjust properly 110-240V
before connecting the equipment to the power inlet. Rating: 100-240V, 50-
60Hz, 1.7A.
8.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
9.
Always unplug the power cord before inserting any add-on card or module.
10.
All cautions and warnings on the equipment should be noted.
11.
Never pour any liquid into the opening that could damage or cause electrical
shock.
12.
If any of the following situations arises, get the equipment checked by
service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well or you can not get it work according to
user
’
s manual.
The equipment has dropped and damaged.
The equipment has obvious sign of breakage.
13.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED,
STORAGE TEMPERATURE ABOVE 40
o
C (102
o
F), IT MAY DAMAGE THE
EQUIPMENT.
WARNING:
1.
For every changes in power cord
’
s usage, please use an approved power
cord with condition greater or equal to H05VV-F, 3G, 0.75mm
2
.
2.
Internal part is hazardous moving parts, please keep fingers and other body
parts away.
3.
For pluggable equipment, the socket-outlet shall be installed near the equip-
ment and shall be easily accessible.
4.
Do not disable the protective earth pin from the plug, the equipment must be
connected to an earthed mains socket-outlet.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.
1.
The optical storage devices are classified as a Class 1 Laser products.
Use of controls or adjustments or performance of procedures other
than those specified.
2.
Do not touch the lens inside the drive.
廢電池請回收
For better environmental protection, waste batteries should be
collected separately for recycling or special disposal.