Mackie ART200A Spec Sheet - Page 6

SPEAKER ART200A Two-Way Active Speaker System ART200A Architects' and Engineers' Specifications The amplified loudspeaker system shall be a self-contained unit, housed in a reinforced polypropylene enclosure and consisting of the following sub-systems: (1) vented twoway loudspeaker system, (2) integrated power amplifiers and crossover network, (3) integrated mic/line input with music and voice equalizers. The loudspeakers shall consist of a 12 inch lowfrequency, cone driver, and a 90° x 70° high-frequency, constant-directivity polynomial horn with a horn-loaded, 1 inch compression driver. The drivers shall be aligned with an analog circuit and crossed over at 1.8kHz by a 4-pole network built into the power amplifiers. Together they shall be capable of producing 122dB SPL (1m, anechoic). Two discrete amplifiers shall be provided, capable of continuously delivering 120W RMS to the low-frequency driver and 40W RMS to the high-frequency driver. Distortion shall be less than 0.1% when measured at 1kHz and 10kHz. They shall be equipped with a multi-function protection circuit to peak limit and protect the loudspeakers from overheating, over-excursion, short circuits and extreme operating temperatures. An indicator lamp shall illuminate when any aspect of the protection circuit engages. The integrated mic/line input shall be actively balanced, may accept an unbalanced input, and shall be paralleled to an output. Both shall have XLR connectors. The input shall have a switch to select between 8mV mic and 125mV line levels. The unit shall be provided with both voice and music optimization equalization that can be activated with buttons on the rear panel. The voice equalizer shall provide +4dB at 3kHz and 6kHz. The music equalizer shall provide +4dB at 65Hz and +4dB at 12kHz. A continuously variable, rotary master volume control shall be provided. The power supply shall be internal and connected to 50 or 60Hz source current through a detachable IEC power cord. It shall have an on/off switch, fuse holder, and threaded grounding screw on the rear panel. AC voltage shall be selectable between 115 and 230VAC. The power supply shall draw a maximum of 2A and illuminate an indicator light when on. The reinforced polypropylene enclosure shall have a volume of at least 1.65 cu. ft., be trapezoidal in shape and equipped with a grille to protect the cone driver. At least four M10 threaded sockets shall be molded into the cabinet for attaching mounting hardware, designed for the unit and (continued Architects' & Engineers' Specs) available from the manufacturer. A full metal grille assembly, covering the front of the enclosure shall be available from the manufacturer. The amplified loudspeaker system shall be a model ART200A manufactured by Mackie Industrial. Electronic files for this product available at: www.mackieindustrial.com This Specification Sheet Quick-Start Manual ART200A.PDF ART200AQS.PDF www.mackieindustrial.com 16220 Wood-Red Rd. NE, Woodinville, WA 98072 USA 888.337.7404, fax 425.487.4337, [email protected] Mackie Designs continually engages in research related to product improvement. New material, produc- tion methods, and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current Mackie Industrial product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated. ©1999-2001 Mackie Designs Inc. All rights Reserved. and are registered trademarks of Mackie Designs Inc. Mackie Industrial is a trademark of Mackie Designs Inc. UK +44.1268.571.212, fax +44.1268.570.809, [email protected] ITALY +39.0522.354.111, fax +39.0522.926.208, [email protected] FRANCE +33.3.8546.9160, fax +33.3.8546.9161, [email protected] GERMANY +49.2572.96042.0, fax +49.2572.96042.10, [email protected] part no. 910-161-10 Rev.B 6 O FoF66 PPAAGGESE S