Mackie MS1202-VLZ Architect's Specs - Page 2
Mixer Input Mixer Output Metering., Physical Configura, Tion., Specifications. - vlz 1202
View all Mackie MS1202-VLZ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
4. MIXER INPUT SECTION. Each channel shall include 1 rotary Trim control; 1 Low Cut filter (HPF), providing an 18dB per octave curve starting at 75Hz; 2 rotary Aux Send controls, providing up to 15dB above unity gain; 3 rotary equalization (EQ) controls: +15dB @ 12kHz shelving, +12dB @ 2.5kHz peaking and +15dB @ 80kHz shelving; 1 rotary Pan control, 4dB attenuation panned center; 1 Mute/Alt 3-4 switch, to be used as a channel mute or to route the signal to the alternate stereo bus (Alt 3-4); 1 PFL (PreFader Listen solo) switch; and 1 rotary channel Gain control, providing up to 20dB above unity gain. Note: The stereo channels (5/6, 7/8, 9/10 and 11/12) shall not include the Trim or Low Cut controls. 5. MIXER OUTPUT SECTION. The mixer shall have 1 rotary Main Mix control, providing up to 10dB above unity gain; 1 rotary Control Room/Phones control, providing up to 10dB above unity gainl; 1 Source Matrix including 3 switches to deliver any combination of stereo signals to the Control Room, Phones and Meters, including Main Mix, Alt 3-4 and Tape, which shall be replaced by any solo signals resulting from the engagement of any channel's PFL switch; 1 Assign to Main Mix switch to deliver the Source Matrix signals to the Main Mix; 2 rotary Aux Return level controls, providing up to 20dB above unity gain; 1 rotary Aux Send 1 Master control, providing up to 10dB above unity gain; 1 Aux Send 1 global Pre/Post switch; 1 EFX to Monitor switch, allowing Aux Return 1 signals to be delivered to Aux Send 1 via the Aux Return 2 level control; and 1 blinking red Solo LED, to indicate a solo condition. 6. METERING. The mixer shall include 1 stereo 12-segment LED meter with points at -30, -20, -10, -7, -4, -2, 0, +2, +4, +7, +10dB and Clip. The source signals for the meters shall be the same signals selected in the Source Matrix, and a solo condition shall replace the Source selection with the soloed channel(s). The meters shall be calibrated so that a 0dBu signal at the Control Room output shall be indicated as 0dB on the meters, ± 1dB. 7. PHYSICAL CONFIGURATION. The mixer shall be made of steel, painted dark gray with light gray graphics. The mixer's dimensions shall be 3.3" (84mm) in height, 11.8" (300mm) in width and 11.2" (284mm) in depth, as viewed horizontally. The mixer shall weigh 6 lbs, 8 oz (14.3 kg). Optional rack-mount brackets shall allow the mixer to be mounted in a rack system, with either the chassis top or the control knobs' tops to be flush with the rack rail. 8. SPECIFICATIONS. In addition to specifications already cited, the mixer shall meet or exceed the following specifications: Frequency response: microphone input to any output, 20Hz to 60kHz, +0dB/-1dB; Total Harmonic Distortion (THD): any input to any output, +14dBu, less than 0.005%; Equivalent Input Noise (EIN): microphone input to insert send, -129.5dBm: Common Mode Rejection (CMR): microphone input to insert send, maximum gain, 1kHz, -85dB; Typical Main Output noise: all channels assigned, channels 1 and 3 panned left, channels 2 and 4 panned right, -86dBu; Signal to Noise ratio: ref +4dBu operating level, 90dB; Attenuation: ref. 0dB @ 1kHz, Main Mix level control down, -85dBu; channel Mute engaged, -84dBu; channel Gain control down, -83dBu; Input impedance: microphones input, 1.3 kilohms; channel Insert return, 2.5 kilohms; all other inputs, greater than 10 kilohms; Output impedance: Tape Out, 1.1 kilohms; all other outputs, 120 ohms. The mixer shall be a Mackie Designs MicroSeries 1202-VLZ, and shall alternatively be referred to as an MS1202-VLZ. Because Mackie Designs constantly endeavors to improve its products with new components and manufacturing methods, all specifications and descriptions are subject to change without notice. ® Rev 1.2 Copyright © 1996-1998 Mackie Designs Inc. "Mackie." and "VLZ" are registered trademarks of Mackie Designs Inc. MACKIE DESIGNS INC. 16220 Wood-Red Road NE • Woodinville, WA 98072 USA Toll-Free 800/258-6883 • FAX 425/487-4337 Outside the U.S., Phone 425/487-4333 • FAX 425/485-1152