Mackie Onyx 4080 Owner's Manual - Page 20
MAIN MIX and PHONES/MONITOR MAIN MIX Faders, SOLO LEVEL, 6². MONITOR Level Control
View all Mackie Onyx 4080 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
ONYX 80 SERIES OO OO OO OO OO OO OO OO OO OO OO OO OO OO OO OO MAX MAX GROUP 5 MAX MAX MAINGR6OMUP IX and PHONES/ MONITOR Section MAX MAX GROUP 7 MAX MAX 60. MAGIRN8OUMP IX Faders MAX MAX These are the master faders that control the levels at LEFT the MMAAX IN OUTS. MAX When MRAIGIHNT MIX TO MON/PHONES [62] is selected in the PMHAXONES/MONITMAOX R Section, the MAIN MIX fader also contArols tMhAeTRmIXain mBix level in the PHONES and MONITOR outpMuAtSsT[ER65/81]. Wh+e15n the faders a+r1e5 fully down, the MAIN MIX is off. The STEREO "U"AmFLarking indicaAteFLs unity gain, and fully up provides 10 dB of additional gain. Typically, these faders are set near MtUhTMeEAG"SURTOE"RUlaPSbel andTAlLeKfBtAaClKone, but they can be used for song fadMeU-oTEuts1or quick system-wide mutes. MAX OO 61. SOLO LEVEL MUTE 2 LEVEL DESTINATION TMhUeTESO3LO LEA1VU-2XEL cA3Uo-4Xntrol is used to adjust the volume of MthUeTEsol4o'ed siAgUnX al 5-6 aAsUXit 7-8 is routed to the MONITOR and PHONES outputs. This control is independent of, and prMioOrNtOo, the MONITOR GRPS 1-8 MAIN L/R and PHONES level controls. OUT This controls the solo signal level for both PFL and AFL solo modes. MAX 62. MAIN PRE FADER TOTALMKBACOK N/PHONES Switch MAIN MIX dB 10 5 U 5 10 20 30 40 50 60 PHONES/ MONITOR SOLO MAX LEVEL MAIN TO MON/PHONES MAX MONITOR MAX PHONES This switch routes the stereo L/R Main Mix signal (post-fader) to both the Monitor and Phones outputs when there are no solo switches engaged. The L/R Main Mix signal is overridden in the Monitor and Phones outputs by any PFL or AFL solo. Note: If a PFL solo switch is engaged, it overrides the AFL solo mode, including MAIN TO MON/PHONES. 63. MONITOR Level Control This controls the signal level at both the Left and Right MONITOR OUTS [81]. 64. PHONES Level Control This controls the signal level at the stereo headphone output [65]. 65. Headphone Jack This is where you plug in your stereo headphones. It is a 1/4" TRS stereo jack and provides the same signal that is routed to the MONITOR outputs [81]. The volume is controlled with the PHONES knob [64]. WARNING: The headphone amp is designed to drive any standard headphones to a very loud level. We're not kidding! It can cause permanent hearing damage. Even intermediate levels may be painfully loud with some headphones. BE CAREFUL! Always start with the PHONES level turned all the way down before connecting headphones to the PHONES jack. Keep it down until you've put on the headphones. Then turn it up slowly. Why? Always remember: "Engineers who fry their ears, find themselves with short careers." 66. Lamp Connectors These 4-pin connectors provide +12 volts DC for gooseneck lamps. The Onyx 2480 has two lamp connectors, while the Onyx 3280, 4080, and 4880 all have three lamp connectors. See your Mackie dealer for gooseneck lamp recommendations (12 V lamps with 4-pin XLR-type connectors). OO OO OO OO OO 20 PREMIUM LIVE ANALOG MIXER WITH PERKINS EQ AND ONYX MIC PREAMPS U GAIN U GAIN U GAIN U GAIN U GAIN U GAIN U GAIN U GAIN -20dB +20dB -20dB +20dB -20dB +20dB -20dB +20dB -20dB +20dB -20dB +20dB -20dB +20dB -20dB +20dB U HIGH ONYX 80 SERIE1S2kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH U HIGH 12kHz -15 +15 U HIGH