Magic Chef M16TG User Guide - Page 10

Operating Instructions

Get Magic Chef M16TG PDF manuals and user guides View all Magic Chef M16TG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

OPERATING INSTRUCTIONS Before operation, please read the user's manual carefully. If the appliance has been immersed in water, please stop using and call the technicians to check and repair or replace all the components that are immersed in the water. Before using this appliance, please make sure that the main burner, pilot light burner and oil receiver are in correct installation. 1. Before igniting the pilot light, ensure there is no gas odor around the device. When first using or after cutting off the gas supply, it may take several minutes to ignite the pilot light due to the air existing in the pipeline or clearance of the inlet pipe. 2. Turn off all gas control knobs. 3. Turn on control valve and light all pilots. 4. The pilot burner must be lit from the top. Hold an ignition source and light the pilot. When the flame is stable, remove ignition source. 5. Turn off the main gas valve to shut down the equipment. NOTE: Control knobs of the burners can be operated manually only. DO NOT rotate it with tools. If it cannot be rotated manually, DO NOT rotate or repair it with force. Force or improper maintenance may cause fire or explosion. NOTE: There may be some smoke at the initial startup as the result of rust prevention coatings burning off. This is normal. Please allow at least a 15 minute burn in period before using for the first time. DAILY INSPECTION It is necessary to check the cooking equipment daily to avoid serious accidents. Stop using if user feels that there are some problems in the circuit or machine. Check the condition of the machine before or after using every day. Before using, make sure the cooking equipment is not tilted and that the control panel is intact. While using, ensure there are no strange smells, light back, flameouts or vibrating noises and that the burner flame is normal. ADJUSTING THE PILOT LIGHT The pilot flame on the equipment has been factory adjusted. When adjustment is necessary, adjust the pilot flames as small as possible but high enough to light the burner immediately when the burner valve is. NOTE: There may be some smoke at the initial startup as the result of rust prevention coatings burning off. This is normal. Please allow at least a 15 minute burn in period before using for the first time. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
10
OPERATING INSTRUCTIONS
Before operation, please read the user’s manual carefully. If the appliance has been immersed in water, please
stop using and call the technicians to check and repair or replace all the components that are immersed in the
water. Before using this appliance, please make sure that the main burner, pilot light burner and oil receiver are
in correct installation.
1.
Before igniting the pilot light, ensure there is no gas odor around the device. When first using or after
cutting off the gas supply, it may take several minutes to ignite the pilot light due to the air existing in the
pipeline or clearance of the inlet pipe.
2.
Turn off all gas control knobs.
3.
Turn on control valve and light all pilots.
4.
The pilot burner must be lit from the top. Hold an ignition source and light the pilot. When the flame is
stable, remove ignition source.
5.
Turn off the main gas valve to shut down the equipment.
NOTE
: Control knobs of the burners can be operated manually only. DO NOT rotate it with tools. If it
cannot be rotated manually, DO NOT rotate or repair it with force. Force or improper maintenance may
cause fire or explosion.
NOTE
: There may be some smoke at the initial startup as the result of rust prevention coatings burning off.
This is normal.
Please allow at least a 15 minute burn in period before using for the first time.
DAILY INSPECTION
It is necessary to check the cooking equipment daily to avoid serious accidents. Stop using if user feels that there
are some problems in the circuit or machine. Check the condition of the machine before or after using every day.
Before using, make sure the cooking equipment is not tilted and that the control panel is intact. While using,
ensure there are no strange smells, light back, flameouts or vibrating noises and that the burner flame is normal.
ADJUSTING THE PILOT LIGHT
The pilot flame on the equipment has been factory adjusted. When adjustment is necessary, adjust the pilot
flames as small as possible but high enough to light the burner immediately when the burner valve is.
NOTE
: There may be some smoke at the initial startup as the result of rust prevention coatings burning off.
This is normal.
Please allow at least a 15 minute burn in period before using for the first time.