Magic Chef MCR16CHM User Guide - Page 7

Installation Instructions

Get Magic Chef MCR16CHM PDF manuals and user guides View all Magic Chef MCR16CHM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

INSTALLATION INSTRUCTIONS Before Using Your Refrigerator • Remove the exterior and interior packing. • Before connecting the refrigerator to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a malfunction in the cooling system from improper handling during transportation. • Clean the interior surface with lukewarm water using a soft cloth. (Cleaning instruction on page 7) Installing Your Refrigerator • This appliance is designed to be free standing only, and should not be recessed or built-in. • Place your refrigerator on a floor that is strong enough to support the refrigerator when it is fully loaded. • Allow 5 inches of space between the back and sides of the refrigerator, which allows the proper air ventilation. Adjust the feet to keep the refrigerator level. • Locate the refrigerator away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Ambient temperature below 50°F or above 85°F will hinder the performance of this appliance. This unit is not designed for use in a garage or any other outside installation. • Avoid locating the refrigerator in moist areas. • Plug the refrigerator into dedicated, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized service center. This unit is not designed to be installed in an RV or used with an inverter. • After plugging the appliance into a wall outlet, turn the unit on and allow the unit to cool down for 2~3 hours under before placing food in the refrigerator. Handle Install Instruction Please note that the Handle parts are inseparable once joined. Please ensure that the handle base is screwed firmly on the door before joining the actual handle part onto its base. 1. Take out the handle from the unit and remove the package. 2. Push the handle horizontally until it clicks in. 3. Push and pull the handle to make sure that it is installed completely. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
4
INSTALLATION INSTRUCTIONS
Before Using Your Refrigerator
•
Re
m
o
v
e the e
x
terior and interior packing.
•
B
efore connecting the refrigerator to the power source, let it stand upright for appro
x
i
m
ately 4 hours.
This will reduce the possibility of a
m
alfunction in the cooling syste
m
fro
m
i
m
proper handling during
transportation.
•
Cl
ean the interior surface with lukewar
m
water using a soft cloth. (
C
leaning instruction on page 7)
Installing Your Refrigerator
•
This appliance is designed to be free standing only, and should not be recessed or built-in.
•
Place your refrigerator on a floor that is strong enough to support the refrigerator when it is fully
loaded.
•
Allow 5 inches of space between the back and sides of the refrigerator, which allows the proper air
v
entilation. Adjust the feet to keep the refrigerator le
v
el.
•
L
ocate the refrigerator away fro
m
direct sunlight and sources of heat (sto
v
e, heater, radiator, etc.).
Direct sunlight
m
ay affect the acrylic coating and heat sources
m
ay increase electrical consu
m
ption.
A
mbie
nt te
mpe
rature below 50°F or abo
ve
85°F will hinder the perf
orma
nce of this appliance.
This
unit is not designed for use in a garage or any other outside installation.
•
A
v
oid locating the refrigerator in
m
oist areas.
•
Plug the refrigerator into dedicated, properly installed-grounded wall outlet. Do not under any
circu
m
stances cut or re
m
o
v
e the third (ground) prong fro
m
the power cord. Any
q
uestions concerning
power and/or grounding should be directed toward a certified electrician or an authorized ser
v
ice
center.
This unit is not designed to be installed in an RV or used with an inverter.
•
After plugging the appliance into a wall outlet, turn the unit on and allow the unit to cool down for 2~3
hours under before placing food in the refrigerat
.
r
o
Handle Install Instruction
Please note that the Handle parts are inseparable once joined. Please ensure that the handle
base is screwed firmly on the door before joining the actual handle part onto its base.
1.
Take out the handle from the unit and remove the package.
2.
Push the handle horizontally until it clicks in.
3.
Push and pull the handle to make sure that it is installed completely.