Magic Chef NPCIM500BIN User Manual - Page 9

Installing The Ice Maker

Get Magic Chef NPCIM500BIN PDF manuals and user guides View all Magic Chef NPCIM500BIN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

INSTALLING THE ICE MAKER 1. Verify that the unit is in good condition and all parts and accessories are present. Check the model and serial number on the label and write them down for reference. 2. Clean all surfaces of the unit, including the ice making area and ice bin with a sponge soaked in warm potable water and soda. Wash and dry the unit thoroughly. 3. Place the unit in the location in which it will be used. Make sure the surface is level and can support the weight, and that there is water drainage near, and plenty of space for ventilation around the unit. 4. Use the adjustable leg levelers if needed to level the ice maker. 5. Connect the machine's inlet water filter and water pipe referring to the schematic diagram of installation; if the installation site is already equipped with a water filtration system, the filter may not be needed. NOTE: Make sure to install the filter so the water is flowing in the direction noted on the filter head cover or filter body. NOTE: This machine is equipped with an inlet water filter. The filter will remove impurities from the water used as the machine is running. Generally, it needs to be replaced every month to every 3 months. 6. Connect the machine to the water supply using the 3/4" inlet pipe supplied with the machine. It is recommended to install a water valve (not supplied with this machine) on the water supply line. 7. Connect the drain pipe to the drain connection. It is recommended that the drain pipe should have a difference of level more than 1 in per 3 ft (3cm per meter); and confirm that the drain pipe is not blocked. It is recommended that the drain pipe be connected to an open drainage port. 8. No part of the drain pipe should be higher than the drain port on the unit, and must not have any inclines. 9. Confirm that all power requirements stated on the ratings label are met, and that the unit is connected to a properly installed, working and grounded circuit breaker. 10. Make sure the power switch is 'Off' before connecting the ice maker to the power supply. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
1.
Verify that the unit is in good condition and all parts and accessories are present. Check the model and serial number on the label and write
them down for reference.
2.
Clean all surfaces of the unit, including the ice making area and ice bin with a sponge soaked in warm potable water and soda. Wash and dry
the unit thoroughly.
5.
3.
Place the unit in the location in which it will be used. Make sure the surface is level and can support the weight, and that there is water
drainage near, and plenty of space for ventilation around the unit.
4.
Use the adjustable leg levelers if needed to level the ice maker.
6.
Connect the machine's inlet water filter and water pipe referring to the schematic diagram of installation; if the installation site is already
equipped with a water filtration system, the filter may not be needed.
NOTE:
Make sure to
install the filter so the water is flowing in the direction noted on the filter head cover or filter body.
NOTE:
This machine is equipped with an inlet water filter. The filter will remove impurities from the water used as the machine is running.
Generally, it needs to be replaced every month to every 3 months.
7.
Connect the machine to the water supply using the 3/4" inlet pipe supplied with the machine. It is recommended to install a water valve
(not supplied with this machine) on the water supply line.
8.
Connect the drain pipe to the drain connection. It is recommended that the drain pipe should have a difference of level more than 1 in per 3
ft (3cm per meter); and confirm that the drain pipe is not blocked. It is recommended that the drain pipe be connected to an open drainage
port.
9.
No part of the drain pipe should be higher than the drain port on the unit, and must not have any inclines.
10.
Confirm that all power requirements stated on the ratings label are met, and that the unit is connected to a properly installed, working and
grounded circuit breaker.
Make sure the power switch is ‘Off’ before connecting the ice maker to the power supply.
INSTALLING THE ICE MAKER
9