Magnavox 26MF321B Owners Manual - Page 12

WATCHING TV, Sleep Timer, Switching Each Input Mode, Freeze Mode, Channel Selection

Get Magnavox 26MF321B PDF manuals and user guides View all Magnavox 26MF321B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

12 WATCHING TV Sleep Timer can set the unit to go into standby mode after an incremental period of time. Press SLEEP repeatedly to change the amount of time (increases Sleep the time by 30 minutes up to 120 minutes). Press SLEEP once to call up the display for checking the remaining time. • To cancel sleep timer, press SLEEP repeatedly until [Sleep Off] is displayed. 120min. Switching Each Input Mode can easily switch with the remote control between TV (ATSC or NTSC) and external devices when they are connected to the unit. Press SOURCE or CH + repeatedly to cycle through the input modes. Source TV HDMI1 HDMI2 Video PC e.g.) 11.1 DTV / TV channel PC HDMI1 HDMI2 Video or Component • Pressing CH − reverses the direction of the input modes. * [Component] will be displayed if you connected component video cables to this unit. Freeze Mode can freeze the image shown on the TV screen for 5 minutes. Press FREEZE to freeze the image. Freeze • The sound output will not be paused. • To cancel freeze mode, press any buttons except . Channel Selection Select channels by using CH +/− or the Number buttons. • To select the memorized channels, use CH +/− or the Number buttons. • To select the non-memorized channels, 11.1 use the Number buttons. To use the Number buttons ATSC -- When selecting digital channel 11.1 Be sure to press • before entering the subchannel number. NTSC -- When selecting cable or analog channel 11 Press PREV CH to return to the previously viewed channel. Note •• [No Signal] will appear on the TV screen after the subchannel broadcast is over. •• [Audio only program] message will appear on the TV screen, when you receive only sound signal.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
WATCHING TV
Sleep Timer
can set the unit to go into standby mode after an incremental period of time.
Press
SLEEP
repeatedly to change the amount of time (increases
the time by 30 minutes up to 120 minutes).
Sleep
120min.
Press
SLEEP
once to call up the display for checking the remaining time.
•
To cancel sleep timer,press
SLEEP
repeatedly until
[Sleep Off]
is
displayed.
Switching Each Input Mode
can easily switch with the remote control
betweenTV (ATSC or NTSC) and external devices when they are connected to the unit.
Press
SOURCE
or
CH +
repeatedly to cycle through the input modes.
Source
TV
HDMI1
HDMI2
Video
PC
e.g.)
11.1
HDMI1
HDMI2
DTV /TV channel
PC
Video
or
Component
•
Pressing
CH −
reverses the direction of the input modes.
*
[Component]
will be displayed if you connected component video cables
to this unit.
Freeze Mode
can freeze the image shown on theTV screen for 5 minutes.
Press
FREEZE
to freeze the image.
Freeze
•
The sound output will not be paused.
•
To cancel freeze mode, press any buttons except
.
Channel Selection
Select channels by using
CH +/−
or
the Number buttons
.
•
To select the memorized channels,
use
CH +/−
or
the Number buttons.
•
To select the non-memorized channels,
use
the Number buttons.
11.1
To use
the Number buttons
ATSC
-
When selecting digital channel 11.1
Be sure to press • before entering the subchannel number.
NTSC
-
When selecting cable or analog channel 11
Press
PREV CH
to return to the previously viewed channel.
Note
•
[No Signal]
will appear on the TV screen after the subchannel
broadcast is over.
•
[Audio only program]
message will appear on the TV screen, when you
receive only sound signal.
12