Makita CA5000X Makita CA5000X Instruction Manual - Page 9

Rip fence guide rule, Stopper for 2 to 3 mm depth of, optional accessory and guide rail, optional

Get Makita CA5000X PDF manuals and user guides View all Makita CA5000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Using circular saw blade Optional accessory CAUTION: In case using circular saw blade, the skirt is not needed and it structually can not be installed. Remove the skirt when using the circular saw blade. To install the circular saw blade (optional accessory), perform the following steps: 1. Remove two bolts, and remove the skirt. 1 Fig.17 ► 1 . Skirt 2. Remove the groove cutter blade. 3. Slide in the circular saw blade from the opening which the skirt had covered. 4. Install the circular saw blade in the same way as the groove cutter blade. And close the blade case door after installing the blade. Fig.19 1 1. Rip fence (guide rule) The handy rip fence allows you to do extra-accurate straight cuts. Simply slide the rip fence up snugly against the side of the workpiece and secure it in position with the screws on the front and the back of the base. It also makes repeated cuts of uniform width possible. Overturning the rip fence (guide rule) also works as a sub base for the tool. Stopper for 2 to 3 mm depth of cut when using circular saw blade (optional accessory) and guide rail (optional accessory) 2 1 1 3 2 4 Fig.18 ► 1 . Hex bolt 2. Outer flange 3. Circular saw blade 4. Inner flange 5. Adjust depth of cut by turning the depth adjusting knob. Rip fence (guide rule) Optional accessory CAUTION: Do not use the rip fence with the groove cutter blade. Use the rip fence only when using the tool with the circular saw blade (optional accessory). Fig.20 ► 1 . Stopper 2. Red mark This tool has the stopper for 2 to 3 mm depth of cut on the gear housing aside the rear handle when using guide rail. Splinter on the workpiece can be avoided by making a pass of the 2 to 3 mm first cut and then make another pass of usual cut. First, push in the stopper toward the circular saw blade for obtaining 2 to 3 mm depth of cut. Then pull the button back for performing free depth of cut. Make sure that the stopper is released and the red mark can be seen for groove cutting operation. 9 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
9
ENGLISH
Using circular saw blade
Optional accessory
CAUTION:
In case using circular saw blade,
the skirt is not needed and it structually can not be
installed. Remove the skirt when using the circular
saw blade.
To install the circular saw blade (optional accessory),
perform the following steps:
1.
Remove two bolts, and remove the skirt.
1
Fig.17
►
1.
Skirt
2.
Remove the groove cutter blade.
3.
Slide in the circular saw blade from the opening
which the skirt had covered.
4.
Install the circular saw blade in the same way as
the groove cutter blade. And close the blade case door
after installing the blade.
1
2
3
4
Fig.18
►
1.
Hex bolt
2.
Outer flange
3.
Circular saw blade
4.
Inner flange
5.
Adjust depth of cut by turning the depth adjusting
knob.
Rip fence (guide rule)
Optional accessory
CAUTION:
Do not use the rip fence with the
groove cutter blade.
Use the rip fence only when
using the tool with the circular saw blade (optional
accessory).
1
Fig.19
1.
Rip fence (guide rule)
The handy rip fence allows you to do extra-accurate
straight cuts. Simply slide the rip fence up snugly
against the side of the workpiece and secure it in
position with the screws on the front and the back of
the base. It also makes repeated cuts of uniform width
possible.
Overturning the rip fence (guide rule) also works as a
sub base for the tool.
Stopper for 2 to 3 mm depth of
cut when using circular saw blade
(optional accessory) and guide rail
(optional accessory)
2
1
Fig.20
►
1.
Stopper
2.
Red mark
This tool has the stopper for 2 to 3 mm depth of cut on the
gear housing aside the rear handle when using guide rail.
Splinter on the workpiece can be avoided by making a
pass of the 2 to 3 mm first cut and then make another
pass of usual cut.
First, push in the stopper toward the circular saw blade
for obtaining 2 to 3 mm depth of cut.
Then pull the button back for performing free depth of
cut.
Make sure that the stopper is released and the red mark
can be seen for groove cutting operation.