Makita EA3201S35B Owners Manual - Page 28

Replacing the saw chain

Get Makita EA3201S35B PDF manuals and user guides View all Makita EA3201S35B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Replacing the saw chain CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare‑parts list)! 11 9 8 12 Check the sprocket before mounting a new chain. Worn out sprockets (8) may damage the new chain and must therefore be replaced. Remove the sprocket guard (See "PUTTING INTO OPERA‑ TION"). Remove the chain and guide bar. Remove circlip (9). CAUTION: The circlip will pop out of the groove. When removing it, hold your thumb against it to prevent it from popping off. Remove thrust washer (11). If the sprocket (8) is worn out, the complete clutch drum (12) will need to be replaced (for the part number, see "Extract from the spare parts list"). Install a complete new clutch drum (12), cup washer (11) and new circlip (9) (for the part numbers, see "Extract from the spare parts list"). For replacing the guide bar, chain, and sprocket see "PUT‑ TING INTO OPERATION". NOTE: Don't use a new chain on a worn chain sprocket. By the time 2 chains have worn, the sprocket has become worn out, so it should be replaced at least at every second chain replacement. To distribute the chain oil evenly, run a new chain at half-throttle for a few minutes before use. New chains stretch, so check the chain tension frequently (see "Checking the chain tension"). 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
28
11
9
12
8
Check the sprocket before mounting a new chain.
Worn out sprockets (
8
) may damage the new chain and must
therefore be replaced.
Remove the sprocket guard (See “PUTTING INTO OPERA
‑
TION”).
Remove the chain and guide bar.
Remove circlip (
9
).
CAUTION:
The circlip will pop out of the groove. When
removing it, hold your thumb against it to prevent it from
popping off.
Remove thrust washer (
11
).
If the sprocket (
8
) is worn out, the complete clutch drum (
12
)
will need to
be replaced (for the part number, see “Extract
from the
spare parts list”).
Install a complete new clutch drum (
12
), cup washer (
11
)
and new circlip (
9
) (for
the part numbers, see “Extract from
the spare parts list”).
For replacing the guide bar, chain, and sprocket see “PUT
‑
TING INTO OPERATION”.
NOTE:
Don’t use a new chain on a worn chain sprocket. By the
time 2 chains have worn, the sprocket has become worn
out, so it should be replaced at least at every second chain
replacement. To distribute the chain oil evenly, run a new
chain at half‑throttle for a few minutes before use.
New chains stretch, so check the chain tension frequently
(see “Checking the chain tension”).
Replacing the saw chain
CAUTION: Use only chains and guide bars designed for this saw
(see the Extract from the spare‑parts list)
!