Makita EB7650TH Instruction Manual - Page 19

Fault location

Page 19 highlights

Fault location Fault Engine not starting or with difficulty System Ignition system Fuel supply Compression Warm start problems Engine starts but dies Mechanical fault Fuel supply Insufficient performance Several systems may simultaneously be affected Observation Ignition spark O.K. No ignition spark Fuel tank filled No compression when pulled over Starter not engaging Tank filled ignition spark existing Tank filled Engine idling poor Cause Fault in fuel supply or compression system, mechanical defect STOP-switch operated, wiring fault or short circuit, spark plug or connector defective, ignition module faulty Incorrect choke position, carburetor defective, fuel supply line bent or blocked, fuel dirty. Cylinder bottom gasket defective, crankshaft seals damaged, cylinder or piston rings defective or improper sealing of spark plug Broken starter spring, broken parts inside of the engine Carburetor contaminated, have it cleaned Incorrect idling adjustment, carburetor contaminated Fuel tank vent defective, fuel supply line interrupted, cable or STOP-switch faulty Air filter contaminated, carburetor contaminated, muffler clogged, exhaust duct in the cylinder clogged Operating time Item Before After operation lubrication Daily (10h) 30h 50h Inspect/clean Engine oil Replace *1 Tightening parts (bolt, nut) Inspect Fuel tank Clean/inspect Drain fuel Throttle trigger/ throttle lever Check function Stop control lever/ stop switch Check function Low-speed rotation Inspect/adjust Air cleaner Clean Ignition plug / plug cord Inspect Cooling air duct Clean/inspect Fuel pipe Inspect Replace Fuel filter Clean/replace Clearance between air intake valve and air discharge valve Adjust Oil tube Inspect Engine overhaul Carburetor Drain fuel *1 Perform initial replacement after 20h operation. *2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop. *3 After emptying the fuel tank, continue to run the engine and drain fuel in the carburetor. 200h Shutdown/ Corresponding rest Page 9 16 18 - *3 18 - 12 13 17 17 18 18 *2 - 18 *2 - *2 - *2 - *3 18 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

19
Fault location
Fault
System
Observation
Cause
Engine not starting or
with difficulty
Ignition system
Ignition spark O.K.
Fault in fuel supply or compression system, mechanical
defect
No ignition spark
STOP-switch operated, wiring fault or short circuit, spark
plug or connector defective, ignition module faulty
Fuel supply
Fuel tank filled
Incorrect choke position, carburetor defective, fuel supply
line bent or blocked, fuel dirty.
Compression
No compression when
pulled over
Cylinder bottom gasket defective, crankshaft seals
damaged, cylinder or piston rings defective or improper
sealing of spark plug
Mechanical fault
Starter not engaging
Broken starter spring, broken parts inside of the engine
Warm start problems
Tank filled ignition spark
existing
Carburetor contaminated, have it cleaned
Engine starts but dies
Fuel supply
Tank filled
Incorrect idling adjustment, carburetor contaminated
Fuel tank vent defective, fuel supply line interrupted, cable
or STOP-switch faulty
Insufficient performance
Several systems may
simultaneously be
affected
Engine idling poor
Air filter contaminated, carburetor contaminated, muffler
clogged, exhaust duct in the cylinder clogged
Operating time
Item
Before
operation
After
lubrication
Daily
(10h)
²0h
³0h
±00h
Shutdown/
rest
Corresponding
Page
Engine oil
Inspect/clean
9
Replace
*1
16
Tightening parts (bolt,
nut)
Inspect
18
Fuel tank
Clean/inspect
Drain fuel
18
Throttle trigger/
throttle lever
Check function
Stop control lever/
stop switch
Check function
Low-speed rotation
Inspect/adjust
Air cleaner
Clean
17
Ignition plug / plug cord
Inspect
17
Cooling air duct
Clean/inspect
18
Fuel pipe
Inspect
18
Replace
Fuel filter
Clean/replace
18
Clearance between
air intake valve and air
discharge valve
Adjust
Oil tube
Inspect
Engine overhaul
Carburetor
Drain fuel
18
*1 Perform initial replacement after 20h operation.
*2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop.
*3 After emptying the fuel tank, continue to run the engine and drain fuel in the carburetor.