Makita EE400MP Instruction Manual - Page 8

Maintenance schedule, Troubleshooting, Technical Data

Get Makita EE400MP PDF manuals and user guides View all Makita EE400MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Maintenance schedule Whole unit Operating hour Before Operation Daily (10h) 30h If required Corresponding page Visually inspect for damaged parts 7 All fixing screws and nuts Tighten 7 Gear case Supply grease 6 Drive axle Supply grease 7 Cutter blade Visually inspect for damage 6 Power unit Refer to the instruction manual of the power unit Troubleshooting Problem The engine does not start. The engine stops soon after its start. The maximum speed is limited. The cutting tool does not rotate. Stop the motor immediately! The unit vibrates abnormally. Stop the motor immediately! The cutting tool does not stop. Stop the motor immediately! Probable cause Refer to the instruction manual of the power unit. Solution The cutting blade is not tightened securely. A twig is caught between the cutting blade and the protector. The drive system does not work properly. The cutting blade is bent, worn or broken. The cutting blade is not tightened securely. The cutting blade is not fitted on the receive washer. The drive system does not work properly. The power unit does not work properly. Tighten the cutting blade securely. Remove the foreign matter. Ask Makita authorized service center to inspect and repair it. Replace the cutting blade with new one. Tighten the cutting blade securely. Install the cutting blade properly. Ask Makita authorized service center to inspect and repair it. Refer to the instruction manual of the power unit. Technical Data Model Dimensions (L x W x H) Net weight (Not including protector and blade) Cutting blade diameter Gear ratio mm (inch) kg (lbs) mm (inch) EE400MP 878 x 131 x 291 (34-1/2" x 5-1/8" x 11-1/2") 2.4 (5.4) 203 (8") 14/29 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
8
Maintenance schedule
Operating hour
Before
Operation
Daily (10h)
30h
If required
Corresponding
page
Whole unit
Visually inspect for damaged
parts
7
All fixing screws and nuts
Tighten
7
Gear case
Supply grease
6
Drive axle
Supply grease
7
Cutter blade
Visually inspect for damage
6
Power unit
Refer to the instruction manual of the power unit
Troubleshooting
Problem
Probable cause
Solution
The engine does not start.
Refer to the instruction manual of the power unit.
The engine stops soon after its start.
The maximum speed is limited.
The cutting tool does not rotate.
Stop the motor immediately!
The cutting blade is not tightened securely.
Tighten the cutting blade securely.
A twig is caught between the cutting blade
and the protector.
Remove the foreign matter.
The drive system does not work properly.
Ask Makita authorized service center to
inspect and repair it.
The unit vibrates abnormally.
Stop the motor immediately!
The cutting blade is bent, worn or broken.
Replace the cutting blade with new one.
The cutting blade is not tightened securely.
Tighten the cutting blade securely.
The cutting blade is not fitted on the receive
washer.
Install the cutting blade properly.
The drive system does not work properly.
Ask Makita authorized service center to
inspect and repair it.
The cutting tool does not stop.
Stop the motor immediately!
The power unit does not work properly.
Refer to the instruction manual of the power
unit.
Technical Data
Model
EE400MP
Dimensions (L x W x H)
mm (inch)
878 x 131 x 291 (34-1/2” x 5-1/8” x 11-1/2”)
Net weight (Not including protector and blade)
kg (lbs)
2.4 (5.4)
Cutting blade diameter
mm (inch)
203 (8”)
Gear ratio
14/29