Makita EX2650LH EX2650LH Instruction Manual - Page 9

Mounting Of Handle, Mounting Attachment

Get Makita EX2650LH PDF manuals and user guides View all Makita EX2650LH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

MOUNTING OF HANDLE CAUTION:  Before doing any work on the Multi Function Power Head, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Multi Function Power Head only after having assembled it completely. Assembling loop handle -- Securely fit the barrier and grip onto the shaft pipe with two screws and clamps. At this time, put the barrier on the left side of the machine as illustrated. -- Make sure that the grip/barrier assembly is located between the spacer and the arrow mark. Do not remove or shrink the spacer. -- Once assembled, do not remove the barrier. CAUTION: Never install the grip on the label or joint. Note: In some countries, the barrier and arrow mark are not provided with the tool. Arrow mark MOUNTING ATTACHMENT CAUTION:  Before doing any work on the Multi Function Power Head, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Multi Function Power Head only after having assembled it completely. Assembly -- Loosen lever. -- Align the attachment's pin with the joint's groove and insert pin. -- Insert attachment up to the arrow position of attachment. And, check to see that button has risen. -- Tighten lever. (See diagram on right for guideline.) Engine Joint 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
9
CAUTION: Before doing any work on the Multi Function Power Head, always
stop the engine and pull the spark plug connector off the spark plug.
Always wear protective gloves!
CAUTION: Start the Multi Function Power Head only after having assembled it
completely.
Assembly
-
Loosen lever.
-
Align the attachment’s pin with the joint’s groove and insert pin.
-
Insert attachment up to the arrow position of attachment.
And, check to see that button has risen.
-
Tighten lever.
(See diagram on right for guideline.)
MOUNTING OF HANDLE
MOUNTING ATTACHMENT
Engine
Joint
CAUTION: Before doing any work on the Multi Function Power Head, always
stop the engine and pull the spark plug connector off the spark plug.
Always wear protective gloves!
CAUTION: Start the Multi Function Power Head only after having assembled it
completely.
Assembling loop handle
-
Securely fit the barrier and grip onto the shaft pipe with two screws and
clamps. At this time, put the barrier on the left side of the machine as
illustrated.
-
Make sure that the grip/barrier assembly is located between the spacer and
the arrow mark. Do not remove or shrink the spacer.
-
Once assembled, do not remove the barrier.
CAUTION: Never install the grip on the label or joint.
Note: In some countries, the barrier and arrow mark are not provided with the
tool.
Arrow mark