Makita GA5040X1 Makita GA5040X1 Instruction Manual - Page 10

Operation with wire cup brush optional, accessory

Get Makita GA5040X1 PDF manuals and user guides View all Makita GA5040X1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

100 mm (4") model Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") 1 Thickness: 4 mm (5/32") or more 2 16 mm (5/8") 3 16 mm (5/8") Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 1 4 20 mm (13/16") 3 20 mm (13/16") 1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Diamond wheel 115 mm (4 - 1/2") / 125 mm (5") / 150 mm (6") model Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") 1 Thickness: 4 mm (5/32") or more Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 1 2 4 22.23 mm (7/8") 22.23 mm (7/8") 3 22.23 mm (7/8") 3 22.23 mm (7/8") 1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Diamond wheel 012746 WARNING: • When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. • NEVER use cut-off wheel for side grinding. • Do not "jam" the wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback, wheel breakage and overheating of the motor may occur. • Do not start the cutting operation in the workpiece. Let the wheel reach full speed and carefully enter into the cut moving the tool forward over the workpiece surface. The wheel may bind, walk up or kickback if the power tool is started in the workpiece. • During cutting operations, never change the angle of the wheel. Placing side pressure on the cut-off wheel (as in grinding) will cause the wheel to crack and break, causing serious personal injury. • A diamond wheel shall be operated perpendicular to the material being cut. Operation with wire cup brush (optional accessory) CAUTION: • Check operation of brush by running tool with no load, insuring that no one is in front of or in line with brush. • Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential for injury from contact with broken brush wires. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
10
Abrasive cut-off wheel
Diamond wheel
Thickness: Less than 4 mm (5/32")
Thickness: 4 mm (5/32") or more
16 mm (5/8")
20 mm (13/16")
22.23 mm (7/8")
Abrasive cut-off wheel
Diamond wheel
Thickness: Less than 4 mm (5/32")
Thickness: 4 mm (5/32") or more
Thickness: Less than 4 mm (5/32")
Thickness: 4 mm (5/32") or more
Thickness: Less than 4 mm (5/32")
Thickness: 4 mm (5/32") or more
22.23 mm (7/8")
22.23 mm (7/8")
22.23 mm (7/8")
16 mm (5/8")
20 mm (13/16")
1
2
3
1
4
3
100 mm (4") model
115 mm (4 - 1/2") / 125 mm (5") / 150 mm (6") model
1
2
3
1
4
3
Lock nut
Abrasive cut-off wheel
Inner flange
Diamond wheel
1.
2.
3.
4.
Lock nut
Abrasive cut-off wheel
Inner flange
Diamond wheel
1.
2.
3.
4.
012746
WARNING:
•
When using an abrasive cut-off / diamond wheel,
be sure to use only the special wheel guard
designed for use with cut-off wheels.
•
NEVER use cut-off wheel for side grinding.
•
Do not "jam" the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in
the cut and the possibility of kickback, wheel
breakage and overheating of the motor may occur.
•
Do not start the cutting operation in the workpiece.
Let the wheel reach full speed and carefully enter
into the cut moving the tool forward over the
workpiece surface.
The wheel may bind, walk up
or kickback if the power tool is started in the
workpiece.
•
During cutting operations, never change the angle
of the wheel. Placing side pressure on the cut-off
wheel (as in grinding) will cause the wheel to crack
and break, causing serious personal injury.
•
A diamond wheel shall be operated perpendicular
to the material being cut.
Operation with wire cup brush (optional
accessory)
CAUTION:
•
Check operation of brush by running tool with no
load, insuring that no one is in front of or in line with
brush.
•
Do not use brush that is damaged, or which is out of
balance. Use of damaged brush could increase
potential for injury from contact with broken brush
wires.