Makita PDC01 PDC01 Instruction Manual - Page 9

Operation

Page 9 highlights

NOTE: You can fold and fix the belt with the hook and loop fastener as shown in the figure. 3. Insert the plug of the adapter or power tool/ machine into the socket of the battery box all the way so that the arrow mark on the plug is aligned with that on the socket. 3 1 2 1 ► 1 . Belt OPERATION CAUTION: When wearing the unit, be sure to put shoulder harness on your both shoulders. Otherwise, the unit may fall when you wear the unit or use the unit, and cause an injury. CAUTION: When wearing the unit, be sure to wear the unit on your back. Otherwise, the unit may fall during operation and cause an injury. CAUTION: Always switch off the tool or machine before turning on the unit, or connecting the plug of the adapter or power tool/machine to the socket of the battery box. Otherwise, the tool or machine may start suddenly and cause an injury. Connecting the unit to the tool or machine 1. Pull out the cord from either left or right side of the battery box. When pulling out the cord, be sure to set the cord in the holders as shown in the figure. 12 ► 1 . Plug 2. Socket 3. Arrow mark NOTICE: When disconnecting the plug and socket, do not hold the cords but hold the plug and socket. Otherwise, the cords may be damaged and cause a malfunction of the unit. NOTE: The plug and socket are disconnected if a certain load is applied. 4. Install the adapters to the tool or machine in the same way as the battery cartridge. 1 ► 1 . Cord 2. Holder 2. Wear the unit. ► 1 . Adapter NOTICE: For 18 V battery-powered tool or machine, use the adapter for 18 V. For 36 V (18 V x 2) battery-powered tool or machine, use the adapters for 36 V (18 V x 2). For direct connection type tool or machine, no adapter is required. 9 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

9
ENGLISH
NOTE:
You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
1
1.
Belt
OPERATION
CAUTION:
When wearing the unit, be sure
to put shoulder harness on your both shoulders.
Otherwise, the unit may fall when you wear the unit or
use the unit, and cause an injury.
CAUTION:
When wearing the unit, be sure to
wear the unit on your back.
Otherwise, the unit may
fall during operation and cause an injury.
CAUTION:
Always switch off the tool or
machine before turning on the unit, or connecting
the plug of the adapter or power tool/machine to
the socket of the battery box.
Otherwise, the tool or
machine may start suddenly and cause an injury.
Connecting the unit to the tool or
machine
1.
Pull out the cord from either left or right side of the
battery box. When pulling out the cord, be sure to set
the cord in the holders as shown in the figure.
2
1
1.
Cord
2.
Holder
2.
Wear the unit.
3.
Insert the plug of the adapter or power tool/
machine into the socket of the battery box all the way so
that the arrow mark on the plug is aligned with that on
the socket.
1
2
3
1.
Plug
2.
Socket
3.
Arrow mark
NOTICE:
When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket.
Otherwise, the cords may be damaged
and cause a malfunction of the unit.
NOTE:
The plug and socket are disconnected if a
certain load is applied.
4.
Install the adapters to the tool or machine in the
same way as the battery cartridge.
1
1.
Adapter
NOTICE:
For 18 V battery-powered tool or
machine, use the adapter for 18 V. For 36 V (18
V x 2) battery-powered tool or machine, use the
adapters for 36 V (18 V x 2).
For direct connection type tool or machine, no
adapter is required.