Marantz DV4100 User Guide - Page 18

Connecting the power cord, Remote control battery installation, NTSC/PAL Settings

Get Marantz DV4100 PDF manuals and user guides View all Marantz DV4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

+ + - ENGLISH TV Connecting to an amplifier equipped with Dolby Surround™ Dolby Surround sound 1 Connect the player to the TV, then connect the player's audio Left and Right out jacks to the corresponding in jacks on the Dolby Surround™ Audio/Video receiver, using the audio/video cable supplied (C). C A B If your amplifier is equipped with a Dolby Digital™ decoder, q Connect the player as described in 'Connecting to an A/V receiver with multi-channel decoder'. DIGITAL OUT AUDIO OUT 1 1 VIDEO OUT 2 2 OPTICAL COAXIAL R L VIDEO CR CB Y S1 If your TV is equipped with a Dolby Surround™ decoder, MODEL N q Connect the player to the TV as described in 'Connecting to a TV'. Connecting the power cord 1 Plug the female end of the supplied power cord into the Mains (AC) jack on the rear of the player. 2 Connect the other end of the cord to an AC outlet. Note: When the player is in the "STANDBY" mode, it is still consuming some power. If you wish to disconnect your player completely from the power, unplug the power cord from the AC outlet. Caution: Only qualified service personnel should remove the cover or attempt to service this device. Remote control battery installation Loading the batteries 1 Open the battery compartment cover. 2 Insert batteries as indicated inside the battery compartment. 3 Close the cover. Caution: Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.) NTSC/PAL Settings You can switch the NTSC/PAL setting of the DVD player to match the video signal of your TV. This setting only affects the television's on-screen display that shows the stop and setup modes. You may select either NTSC or PAL. To change the DVD player setting to PAL or NTSC, follow the steps below. 1 Unplug the DVD player from the mains. 2 Press and hold 9 and T on the front of the DVD player. While holding 9 and T, plug in the mains. 3 After PAL or NTSC appears on the display panel of the DVD player, release 9 and T at the same time. The PAL or NTSC that appears on the display panel indicates the current setting. 4 To change the setting, press T within three seconds. The new setting (PAL or NTSC) will appear on the display panel. 18 PREPARATION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
18 PREPARATION
ENGLISH
Connecting to an amplifier equipped with Dolby
Surround™
Dolby Surround sound
1
Connect the player to the TV, then connect the player’s audio Left
and Right out jacks to the corresponding in jacks on the Dolby
Surround™ Audio/Video receiver, using the audio/video cable
supplied
(C)
.
If your amplifier is equipped with a Dolby Digital™ decoder,
●
Connect the player as described in ‘Connecting to an A/V receiver
with multi-channel decoder’.
If your TV is equipped with a Dolby Surround™ decoder,
●
Connect
the player to the TV as described in ‘Connecting to a TV’.
Connecting the power cord
1
Plug the female end of the supplied power cord into the Mains (AC) jack
on the rear of the player.
2
Connect the other end of the cord to an AC outlet.
Note:
When the player is in the “STANDBY” mode, it is still
consuming some power. If you wish to disconnect your player
completely from the power, unplug the power cord from the AC
outlet.
Caution: Only qualified service personnel should remove the cover
or attempt to service this device.
Remote control battery installation
Loading the batteries
1
Open the battery compartment cover.
2
Insert batteries as indicated inside the battery compartment.
3
Close the cover.
Caution: Do not mix old and new batteries. Never mix
different types of batteries (standard, alkaline, etc.)
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to match
the video signal of your TV. This setting only affects the television’s
on-screen display that shows the stop and setup modes. You may
select either NTSC or PAL. To change the DVD player setting to
PAL or NTSC, follow the steps below.
1
Unplug the DVD player from the mains.
2
Press and hold
9
and
T
on the front of the DVD player. While
holding
9
and
T
, plug in the mains.
3
After PAL or NTSC appears on the display panel of the DVD
player, release
9
and
T
at the same time. The PAL or NTSC
that appears on the display panel indicates the current setting.
4
To change the setting, press
T
within three seconds. The new
setting (PAL or NTSC) will appear on the display panel.
+
-
+
-
MODEL N
AUDIO OUT
VIDEO OUT
DIGITAL OUT
S1
C
C
Y
2
1
2
1
OPTICAL
COAXIAL
R
L
VIDEO
TV
C
B
A