Marantz M-CR603 SR6006 Home Theater Receiver - Page 2

Phono equalizer PHONO input - REC OUT - rating

Page 2 highlights

SR6006 Home Theater Receiver Audio Section • Power amplifier Rated output: Front: 110 W + 110 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Center: 110 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Surround: 110 W + 110 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Surround back: 110 W + 110 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Output connectors: (SPEAKER A+B: 8 Ω) • Analog Input sensitivity/Input impedance: 200 mV/47 kΩ Frequency response: 10 Hz - 100 kHz - +1, -3 dB (DIRECT mode) S/N: 100 dB (IHF-A weighted, DIRECT mode) Distortion: 0.005 % (20 Hz - 20 kHz) (DIRECT mode) Rated output: 1.2 V • Digital D/A output: Rated output - 2 V (at 0 dB playback) Total harmonic distortion - 0.008 % (1 kHz, at 0 dB) S/N ratio - 102 dB Dynamic range - 100 dB Digital input: Format - Digital audio interface • Phono equalizer (PHONO input - REC OUT) Input sensitivity: 2.5 mV RIAA deviation: ±1 dB (20 Hz to 20 kHz) S/N: 74 dB (A weighting, with 5 mV input) Rated output: 150 mV Distortion factor: 0.03 % (1 kHz, 3 V) Video Section • Standard video connectors Input/output level and impedance: 1 Vp-p, 75 Ω Frequency response: 5 Hz - 10 MHz - 0, -3 dB (when "Video Convert" set to "OFF") • Color component video connector Input/output level and impedance: Y (brightness) signal - 1 Vp-p, 75 Ω PB / CB signal - 0.7 Vp-p, 75 Ω PR / CR signal - 0.7 Vp-p, 75 Ω Frequency response: 5 Hz - 60 MHz - 0, -3 dB (when "Video Convert" set to "OFF") Tuner Section [FM] [AM] (Note: μV at 75 Ω, 0 dBf = 1 x 10-15 W) Receiving Range: 87.5 MHz - 107.9 MHz 530 kHz - 1710 kHz Usable Sensitivity: 1.5 μV (14.8 dBf) 20 μV S/N: MONO 78 dB (IHF-A weighted, DIRECT mode) STEREO 68 dB (IHF-A weighted, DIRECT mode) HD 85 dB 85 dB Total harmonic Distortion (at 1 kHz): MONO 0.1 % STEREO 0.2 % HD 0.02 % 0.02 % General Power supply: AC 120 V, 60 Hz Power consumption: 650 W 0.2 W (Standby) 2.2 W (CEC standby) For purposes of improvement, specifications and design are subject to change without notice. All specifications, dimensions and weights are subject to change without notice. D&M Holdings, Marantz, Marantz America, LLC. or any of its subsidiaries will not assume any liability for errors in this spec sheet which may result in consequential errors Being made by dealers, designers, custom installers, cabinet makers or end users, etc based upon information contained within this document. ©2011 Marantz America, LLC · www.marantz.com

  • 1
  • 2

©2011 Marantz America, LLC · www.marantz.com
All specifications, dimensions and weights are subject to change without notice.
D&M Holdings, Marantz, Marantz America, LLC. or any of its subsidiaries will not assume any liability for errors in this spec sheet which may result in consequential errors
Being made by dealers, designers, custom installers, cabinet makers or end users, etc based upon information contained within this document.
SR6006 Home Theater Receiver
Audio Section
Power amplifier
Rated output:
Front:
110 W + 110 W (8
, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Center:
110 W (8
, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Surround:
110 W + 110 W (8
, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Surround back:
110 W + 110 W (8
, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Output connectors:
(SPEAKER A+B: 8
)
Analog
Input sensitivity/Input impedance:
200 mV/47 k
Frequency response:
10 Hz – 100 kHz — +1, –3 dB (DIRECT
mode)
S/N:
100 dB (IHF–A weighted, DIRECT mode)
Distortion:
0.005 % (20 Hz – 20 kHz) (DIRECT mode)
Rated output:
1.2 V
Digital
D/A output:
Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input:
Format — Digital audio interface
Phono equalizer (PHONO input — REC OUT)
Input sensitivity:
2.5 mV
RIAA deviation:
±1 dB (20 Hz to 20 kHz)
S/N:
74 dB (A weighting, with 5 mV input)
Rated output:
150 mV
Distortion factor:
0.03 % (1 kHz, 3 V)
Video Section
Standard video connectors
Input/output level and impedance:
1 Vp-p, 75
Frequency response:
5 Hz – 10 MHz — 0, –3 dB
(when “Video Convert” set to “OFF”)
Color component video connector
Input/output level and impedance:
Y (brightness) signal — 1
Vp-p, 75
PB / CB signal — 0.7 Vp-p, 75
PR / CR signal — 0.7 Vp-p, 75
Frequency response:
5 Hz – 60 MHz — 0, –3 dB (when “Video
Convert” set to “OFF”)
Tuner Section [FM] [AM]
(Note:
μ
V at 75
, 0 dBf = 1 x 10–15 W)
Receiving Range:
87.5 MHz – 107.9 MHz 530 kHz – 1710 kHz
Usable Sensitivity:
1.5
μ
V (14.8 dBf) 20
μ
V
S/N:
MONO 78 dB (IHF–A weighted, DIRECT mode)
STEREO 68 dB (IHF–A weighted, DIRECT mode)
HD 85 dB 85 dB
Total harmonic Distortion (at 1 kHz):
MONO 0.1 %
STEREO 0.2 %
HD 0.02 % 0.02 %
General
Power supply:
AC 120 V, 60 Hz
Power consumption:
650 W
0.2 W (Standby)
2.2 W (CEC standby)
For purposes of improvement, specifications and design are sub-
ject to change without notice.