Marantz SR4002 SR4002_Rear_Panel_Drawing - Page 19
Basic Operation - reset
View all Marantz SR4002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
ENGLISH BASIC OPERATION NORMAL MODE (When operating Marantz AV equipment products) This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier). Learning is not necessary for Marantz products. You can use these products without setting any codes. 1. Press the SOURCE button. For this example, press DVD. Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed. To change the amplifier on other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifier source changes to DVD. SETTING THE BACK LIGHT Each time press the buttons, illuminate button 2 seconds. To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice. Initial is back light ON. PRESET MODE (When operating non-Marantz AV equipment products) This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, VCR, DVD and DSS. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the source button of the remote controller. See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings. Remote controller Corresponding preset Device name source name code TV TV Television DVD DVD DVD player VCR VCR Video deck DSS SATELLITE Satellite broadcasting tuner equipment 16 Importants: • Some codes may be not match your equipment. In this case, you can use LEARN mode to store these codes. • The preset codes do not cover full functions. If you need extra function, use LEARN mode to store extra function. • Wen the batteries are getting weak, the preset procedure is not successful. PROGRAMMING WITH THE 4-DIGIT CODE 1. - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER 1. 2. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME 1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flushes. 2. Press the 4-digit code for appliance (code table at the end of this book) When the procedure is successful, the SEND indicator will blink twice. Note: If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again. SCANNING THE CODE TABLE 2. 2. LEARN SEND SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 1 CS 4 2 EX/ES 5 LIP SYNC/ dts INPUT 3 VIRTUAL T.MODE 6 DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER 3. 3. 5. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU T.TONE /SET UP ENTER EXIT 1. Switch on the appliance which should be controlled. 2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes. 3. Aim the remote control at the appliance and slowly alternate between pressing CH+ button and the SOURCE ON/OFF button for the appliance. 4. Stop when the appliance turns off. 5. Press ENTER button once to lock in the code. CHECKING THE CODE 1. 1. LEARN SEND SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 3. 4. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER 2. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU T.TONE /SET UP ENTER EXIT 1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light flushes. 2. Press the INFO button. The SEND indicator will blink twice. 3. To view the code for first digit, press 1 once. Wait 3 seconds, count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number. Note: If a code digit is "0", the SEND indicator will not blink. 4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. RESETTING THE CODE LEARN SEND LEARN SEND 1. 1. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER 2. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU 1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes. 2. Press the below codes to reset. TV : 1000 DVD : 2000 VCR : 3000 DSS : 4000 The indicator will blink twice. Note: After this procedure, the selected SOURCE button is set initial code.