Maytag M8RXNGMBW Owners Manual - Page 11

Troubleshooting

Page 11 highlights

Changing the Light Bulbs NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape, and wattage. Freezer Light Refrigerator Light 1. Unplug refrigerator or disconnect power. 2. Reach behind the control panel and unscrew the bulb. 3. Replace the bulb with a 40-watt appliance bulb. 4. Plug in refrigerator or reconnect power. 1. Unplug refrigerator or disconnect power. 2. Remove the freezer shelf. 3. Remove the freezer light shield by pushing down. 4. Remove the light bulb and replace with one of the same size, shape and wattage. 5. Replace the light shield. 6. Plug in refrigerator or reconnect power. TROUBLESHOOTING First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call. In the U.S.A., www.maytag.com In Canada, www.maytag.ca The refrigerator will not operate WARNING Refrigerator Operation ■ Control(s) on? Make sure the refrigerator control is on. See "Using the Control(s)." ■ New installation? Allow 24 hours following installation for the refrigerator to cool completely. NOTE: Adjusting the temperature control(s) to coldest setting will not cool the refrigerator more quickly. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. ■ Power cord unplugged? Plug into a grounded 3 prong outlet. ■ Is outlet working? Plug in a lamp to see if the outlet is working. ■ Household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. The motor seems to run too much Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, the door is opened often, or if the door has been left open. The refrigerator seems noisy Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with explanations. ■ Pulsating - fans/compressor adjusting to optimize performance. ■ Hissing/Rattling - flow of refrigerant, movement of water lines, or from items placed on top of the refrigerator. ■ Popping - contraction/expansion of inside walls, especially during initial cool-down. ■ Water running/dripping - may be heard when ice melts during defrosting and water runs into the drain pan. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

11
Changing the Light Bulbs
NOTE:
Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size, shape, and wattage.
Refrigerator Light
1.
Unplug refrigerator or disconnect power.
2.
Reach behind the control panel and unscrew the bulb.
3.
Replace the bulb with a 40-watt appliance bulb.
4.
Plug in refrigerator or reconnect power.
Freezer Light
1.
Unplug refrigerator or disconnect power.
2.
Remove the freezer shelf.
3.
Remove the freezer light shield by pushing down.
4.
Remove the light bulb and replace with one of the same size,
shape and wattage.
5.
Replace the light shield.
6.
Plug in refrigerator or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
In the U.S.A., www.maytag.com
In Canada, www.maytag.ca
Refrigerator Operation
The refrigerator will not operate
Power cord unplugged?
Plug into a grounded 3 prong
outlet.
Is outlet working?
Plug in a lamp to see if the outlet is
working.
Household fuse blown or circuit breaker tripped?
Replace
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
Control(s) on?
Make sure the refrigerator control is on. See
“Using the Control(s).”
New installation?
Allow 24 hours following installation for
the refrigerator to cool completely.
NOTE:
Adjusting the temperature control(s) to coldest setting
will not cool the refrigerator more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, the door is
opened often, or if the door has been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below
are listed some normal sounds with explanations.
Pulsating
- fans/compressor adjusting to optimize
performance.
Hissing/Rattling
- flow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator.
Popping
- contraction/expansion of inside walls, especially
during initial cool-down.
Water running/dripping
- may be heard when ice melts
during defrosting and water runs into the drain pan.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING