Maytag MDB7749SAW Use & Care Guide - Page 7

Dishwasher Feedback - model #

Get Maytag MDB7749SAW PDF manuals and user guides View all Maytag MDB7749SAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Dishwasher Feedback Section CONTROLS AND CYCLE STATUS CONTROL PURPOSE COMMENTS The Cycle Status Indicator Lights are used to follow the progress of the dishwasher cycle. Located on the front of the dishwasher for front control models, and located on the top of the door for hidden control models. Clean indicator glows when a cycle is finished. If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required temperature. The Clean and Sanitized lights go off when you open and close the door or press CANCEL. Canceling A Cycle 1. Open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door. 2. Press CANCEL/DRAIN button once. The Cancel/Drain light will light up. 3. Close the door and the dishwasher starts a drain cycle (if water remains in bottom of dishwasher). Let the dishwasher drain completely. The Cancel/Drain light turns off after 2 minutes. Changing A Cycle After Dishwasher Is Started 1. You can interrupt a cycle and restart your dishwasher from the beginning using the following procedure. 2. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely. 3. Check that detergent dispenser cover is still closed. If cover is open, you will need to refill the detergent dispenser before restarting your new cycle. 4. Press CANCEL/DRAIN twice to reset the control. 5. Select new cycles and options. 6. Press START/RESUME. Adding A Dish After Dishwasher Is Started 1. Check if Add a Dish indicator is lit. (Available on some models. Otherwise, proceed to Step 2.) 2. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely. 3. Check whether the detergent dispenser cover is still closed. If it is open, the wash cycle has already started and adding a dish is not recommended. 4. If detergent has not yet been used (detergent dispenser cover is closed), you may add a dish. 5. Press START/RESUME. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
7
Dishwasher Feedback Section
Canceling A Cycle
1.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop before completely opening the door.
2.
Press CANCEL/DRAIN button once. The Cancel/Drain light will
light up.
3.
Close the door and the dishwasher starts a drain cycle (if water
remains in bottom of dishwasher). Let the dishwasher drain
completely. The Cancel/Drain light turns off after 2 minutes.
Changing A Cycle After Dishwasher Is Started
1.
You can interrupt a cycle and restart your dishwasher from the
beginning using the following procedure.
2.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3.
Check that detergent dispenser cover is still closed. If cover is
open, you will need to refill the detergent dispenser before
restarting your new cycle.
4.
Press CANCEL/DRAIN twice to reset the control.
5.
Select new cycles and options.
6.
Press START/RESUME.
Adding A Dish After Dishwasher Is Started
1.
Check if Add a Dish indicator is lit. (Available on some models.
Otherwise, proceed to Step 2.)
2.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3.
Check whether the detergent dispenser cover is still closed. If
it is open, the wash cycle has already started and adding a
dish is not recommended.
4.
If detergent has not yet been used (detergent dispenser cover
is closed), you may add a dish.
5.
Press START/RESUME.
CONTROLS AND CYCLE STATUS
CONTROL
PURPOSE
COMMENTS
The Cycle Status Indicator
Lights are used to follow the
progress of the dishwasher
cycle. Located on the front
of the dishwasher for front
control models, and located
on the top of the door for
hidden control models.
Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished,
the Sanitized indicator glows. If your dishwasher did not properly sanitize
your dishes, the light flashes at the end of the cycle. This can happen if the
cycle is interrupted, or the water could not be heated to the required
temperature.
The Clean and Sanitized lights go off when you open and close the door or
press CANCEL.