Maytag MED6630HC Instruction Sheet - Page 1

Maytag MED6630HC Manual

Get Maytag MED6630HC PDF manuals and user guides View all Maytag MED6630HC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Inlet Hose Connection Instructions for Steam Dryers Instrucciones para la conexión de la manguera de entrada para secadoras con vapor Instructions de raccordement du tuyau d'arrivée d'eau pour les sécheuses avec vapeur INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation. The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. Tools needed: Parts Supplied: Pliers "Y" connector Rubber washer Parts needed: (Not supplied with dryer) 5' (1.5 m) Inlet Hose Your installation may require additional parts. To order, please contact the dealer from whom you purchased your dryer or an authorized service company. 2' (0.6 m) Inlet hose CONNECT INLET HOSES 1. Turn cold water faucet off and remove washer inlet hose. 7. Using pliers, tighten the couplings an additional two-thirds turn. 2. Remove old rubber washer from inlet hose and replace with new rubber washer provided. Inspect hoses to be sure rubber washers are in place. 3. Attach 2' (0.6 m) inlet hose to cold water faucet. Screw on coupling by hand until it is seated on faucet. NOTE: Do not overtighten. Damage to the coupling can result. 8. Attach other end of 5' (1.5 m) inlet hose to fill valve at bottom or top of dryer back panel (depending on model). Screw on coupling by hand until it is seated on fill valve connector. 4. Using pliers, tighten the couplings with an additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result. 5. Attach "Y" connector to the end of small hose. Screw on coupling by hand until it is seated on connector. 6. Attach dryer 5 ft (1.5 m) inlet hose ends to the "Y" connector. Attach washer cold inlet hose to other side of "Y" connector. Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings an additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result. 9. Using pliers, tighten the couplings an additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result. 10. C heck that the water faucets are on. 11. C heck for leaks around "Y" connector, faucet, and hoses. W10701405A

  • 1
  • 2
  • 3
  • 4
Inlet Hose Connection Instructions for Steam Dryers
Instrucciones para la conexión de la manguera
de entrada para secadoras con vapor
Instructions de raccordement du tuyau d’arrivée
d’eau pour les sécheuses avec vapeur
TOOLS AND PARTS
Gather the required tools and parts before starting installation. The dryer must be
connected to the cold water faucet using the new inlet hoses. Do not use old hoses.
INSTALLATION REQUIREMENTS
2' (0.6 m) Inlet hose
5' (1.5 m) Inlet Hose
Rubber washer
Parts needed:
(Not supplied with dryer)
Pliers
W10701405A
CONNECT INLET HOSES
1.
Turn cold water faucet off and remove washer inlet hose.
2.
Remove old rubber washer from inlet hose and replace
with new rubber washer provided. Inspect hoses to be sure
rubber washers are in place.
3.
Attach 2' (0.6 m) inlet hose to cold water faucet. Screw on
coupling by hand until it is seated on faucet.
4.
Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE:
Do not overtighten. Damage to the coupling can result.
5.
Attach “Y” connector to the end of small hose. Screw on
coupling by hand until it is seated on connector.
6.
Attach dryer 5 ft (1.5 m) inlet hose ends to the “Y” connector.
Attach washer cold inlet hose to other side of “Y” connector.
Screw on coupling by hand until it is seated on connector.
Using pliers, tighten the couplings an additional two-thirds turn.
NOTE:
Do not overtighten. Damage to the coupling can result.
7.
Using pliers, tighten the couplings an additional two-thirds turn
.
NOTE:
Do not overtighten. Damage to the coupling can result.
8.
Attach other end of 5' (1.5 m) inlet hose to fill valve at bottom
or top of dryer back panel (depending on model). Screw on
coupling by hand until it is seated on fill valve connector.
9.
Using pliers, tighten the couplings an additional two-thirds turn
.
NOTE:
Do not overtighten. Damage to the coupling can result.
10.
Check that the water faucets are on.
11.
Check for leaks around “Y” connector, faucet, and hoses.
“Y” connector
Parts Supplied:
Your installation may require
additional parts. To order,
please contact the dealer
from whom you purchased
your dryer or an authorized
service company.
Tools needed: