Maytag MEDE201YW Installation Guide
Maytag MEDE201YW Manual
 |
View all Maytag MEDE201YW manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MEDE201YW manual content summary:
- Maytag MEDE201YW | Installation Guide - Page 1
Connection 11 VENTING 14 Venting Requirements 14 Plan Vent System 15 Venting Kits 15 Install Vent System 16 CONNECT INLET HOSE 17 CONNECT VENT 18 LEVEL DRYER 19 COMPLETE INSTALLATION CHECKLIST 19 DOOR REVERSAL KIT (OPTIONAL 20 STACKING WASHER AND DRYER (OPTIONAL 20 TROUBLESHOOTING 20 - Maytag MEDE201YW | Installation Guide - Page 2
DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2 - Maytag MEDE201YW | Installation Guide - Page 3
in dryer drum. Check that all parts are included. NOTE: Do not use leveling legs supplied if installing with a pedestal or a stack kit. Utility knife Tape measure Leveling legs (4) "Y" connector (steam models only) Level Pliers Caulking gun and compound (for installing new exhaust vent - Maytag MEDE201YW | Installation Guide - Page 4
is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly. ■■For garage installation, place dryer at least 18" (460 mm) above floor. If using a pedestal, you will need 18" (460 - Maytag MEDE201YW | Installation Guide - Page 5
All dimensions show recommended and minimum spacing allowed. ■■Additional spacing should be considered for ease of installation and servicing. ■■Additional clearances might be required for wall, door, floor moldings, dryer venting, and gas line. ■■Additional spacing should be considered on all sides - Maytag MEDE201YW | Installation Guide - Page 6
new branch-circuit installations after 1996, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors. If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain - Maytag MEDE201YW | Installation Guide - Page 7
INSTALL LEVELING LEGS 1. Prepare dryer for leveling legs To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. 2. Screw in leveling legs diamond - Maytag MEDE201YW | Installation Guide - Page 8
For power supply cord installations: For direct wire installations: Before you start: disconnect power. 1. Choose electrical to neutral wire, go to "Optional 3-wire connection". This connection may be used with either a power supply cord or a direct wire connection. Remove hold-down screw and - Maytag MEDE201YW | Installation Guide - Page 9
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. A 4-wire receptacle (NEMA strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain - Maytag MEDE201YW | Installation Guide - Page 10
of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Connect neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Tighten screw. 3. Connect remaining wires 3-Wire Power Supply Cord Connection Use - Maytag MEDE201YW | Installation Guide - Page 11
Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 1. (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, - Maytag MEDE201YW | Installation Guide - Page 12
outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape wire terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. 12 Place hooked end - Maytag MEDE201YW | Installation Guide - Page 13
terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Optional External Ground for block screws. Tighten screws. A 4. Connect external ground wire Install the correct strain relief for your electrical connection method, as shown - Maytag MEDE201YW | Installation Guide - Page 14
and supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install in enclosed walls, ceilings, or floors. ■■ The total length should not exceed 73/4 ft. (2.4 m). ■■ The length of flexible metal vent used - Maytag MEDE201YW | Installation Guide - Page 15
) Periscope installation Special provisions for mobile homes: Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the mobile home. Terminate exhaust vent outside. If you prefer, dryer may be converted to exhaust out right side, left side - Maytag MEDE201YW | Installation Guide - Page 16
best drying performance. NOTE: Side and bottom exhaust installation have a 90° turn inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart. Install Vent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use caulking compound - Maytag MEDE201YW | Installation Guide - Page 17
HOSE (Steam models only) For non-steam models, proceed to "Connect Vent". The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement - Maytag MEDE201YW | Installation Guide - Page 18
can result. 6. Turn on cold water faucet Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 - Maytag MEDE201YW | Installation Guide - Page 19
any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read "Dryer Use" in your Use and Care Guide. q For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on Power. Steam Models Only: q Be sure - Maytag MEDE201YW | Installation Guide - Page 20
to reverse the door swing on your dryer: A door reversal kit, Part Number W10406955 is available to order. For further information, see "Assistance or Service" section in your Use and Care Guide. STACKING WASHER AND DRYER (OPTIONAL) If you prefer to stack your washer and dryer: A stack kit, Part
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
W10385103B
W10385104B - SP
Table of Contents
DRYER SAFETY
.........................................................................
2
INSTALLATION REQUIREMENTS
.............................................
3
Tools and Parts
......................................................................
3
LOCATION REQUIREMENTS
....................................................
4
ELECTRICAL REQUIREMENTS
................................................
6
INSTALL LEVELING LEGS
.........................................................
7
ELECTRICAL INSTALLATION
...................................................
8
Power Supply Cord Connection
...........................................
9
Direct Wire Connection
.......................................................
11
VENTING
...................................................................................
14
Venting Requirements
.........................................................
14
Plan Vent System
.................................................................
15
Venting Kits
..........................................................................
15
Install Vent System
..............................................................
16
CONNECT INLET HOSE
..........................................................
17
CONNECT VENT
......................................................................
18
LEVEL DRYER
..........................................................................
19
COMPLETE INSTALLATION CHECKLIST
..............................
19
DOOR REVERSAL KIT (OPTIONAL)
.......................................
20
STACKING WASHER AND DRYER (OPTIONAL)
...................
20
TROUBLESHOOTING
..............................................................
20
ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
Date of purchase:
_________________________________
Date of installation:
_______________________________
Installer:
________________________________________
Model number:
___________________________________
Serial number:
___________________________________
Para una version de estas instrucciones en español, visite www.Whirlpool.com