Maytag MES8800FZ Installation Guide - Page 3
Installation Requirements - trim kit
View all Maytag MES8800FZ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■ Tape measure ■ Masking tape ■ Flat-blade screwdriver ■ ¼" (6.4 mm) drive ratchet ■ Phillips screwdriver ■ Level ■ Hand or electric drill ■ Wrench or pliers ■ Marker or pencil ■ ¼" (6.4 mm) nut driver 9.5 mm) and 8 mm) nut driver 3.2 mm) drill bit (for wood floors) ■ Tin snips or large wire cutters (for cutting ground strap if necessary) Parts Supplied Check that all parts are included. ■ 10-32 hex nuts (attached to terminal block) (3) ■ Direct wire lugs (3) ■ #10 x 1⁵⁄₈" (4.1 cm) screws (for mounting anti-tip bracket) (2) ■ Anti-tip bracket (inside oven cavity) Anti-tip bracket must be securely mounted to the back wall or floor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. ■ For Models: WEC530H0D WEE730H0D YWEE730H0D JES1450CD JES1450D KSEG700E KSEB900E KSIB900E MES8880D WEE760H0D YKSEG700E YKSEB900E YKSIB900E YMES8880D YWEE760H0D Oven Racks 2 3 Parts Needed If using a power supply cord kit: ■ A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends. ■ A UL listed strain relief. Check local codes. Check existing electrical supply. See the appropriate "Electrical Requirements" section. It is recommended that all electrical connections be made by a licensed, qualified electrical installer. Optional Parts To purchase these or any other accessories, please reference the "Accessories" section of the User Guide for contact information. ■ Side Trim Kits 1.7 cm) White - Order Part Number W10675027 1.7 cm) Black - Order Part Number W10675026 1.7 cm) Stainless Steel - Order Part Number W10675028 1¹⁄₈" (2.9 cm) White - Order Part Number W10731885 1¹⁄₈" (2.9 cm) Black - Order Part Number W10731886 1¹⁄₈" (2.9 cm) Stainless Steel - Order Part Number W10731887 ■ Backsplash Kits: High 6" (15.2 cm) White - Order Part Number W10655448 High 6" (15.2 cm) Black - Order Part Number W10655449 High 6" (15.2 cm) Stainless Steel - Order Part Number W10655450 Location Requirements IMPORTANT: Observe all governing codes and ordinances. ■ It is the installer's responsibility to comply with installation clearances specified on the model/serial/rating plate. The model/serial/rating plate is located behind the oven door on the top right-hand side of the oven frame. ■ The range should be located for convenient use in the kitchen. ■ Recessed installations must provide complete enclosure of the sides and rear of the range. ■ To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood or microwave hood combination that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets. ■ All openings in the wall or floor where range is to be installed must be sealed. 3