Maytag MGR4452BDB Installation Manual - Page 4

ANTI-TIP

DEVICE

INSTALLATION

INSTRUCTIONS

NOTE:

A risk of range

tip over

exists

if

the

appliance

is

not

installed

in accordance

with

the

installation

instructions

provided.

The

proper

use of this

device

minimizes

the

risk of TIP-OVER.

In using

this device

the

consumer

must

still observe

the

safety

precautions

as

stated

in the

USE

and

CARE

MANUAL

and avoid

using

the

oven

door

and/or

lower

drawer

as a step

stool.

Installation

instructions

are provided

for wood

and cement

in either

floor

or wall.

Any

other

type

of construction

may

require

special

installation

techniques

as deemed

necessary

to provide

adequate

fastening

of the

ANTI-TIP

bracket

to the

floor

or wall.

STEP

1

-

Locating

The

Bracket

(see

figure

1)

A.

Determine

where

either

the

right

or left rear

"edge"

of

the

range

will be located

and mark

the

floor

or wall.

g.

C.

Place

the

BRACKET

15/16"

(24 mm)

from

the

marked

"EDGE"

toward

center

of opening

and against

the

back

wall

as shown

in figure

1, with

orientation

hole

against

wall.

Use

the bracket

as a template

and

mark

the

required

holes,

as shown

in figure

1 for the type

of construction

you

will

be using.

STEP

2 - Anti-Tip

Bracket

Installation

A.

Wood

Construction:

1.

Floor:

Locate

the

center

of the

two holes

identified

in figure

1 as "HOLES

FOR

FLOOR".

Drill

a 1/8"

(3 mm)

pilot

hole

in

the

center

of each

hole

(a nail

or awl may

be used

if

a drill is not

available).

Secure

the

ANTI-TIP

bracket

to the floor

with

the

two screws

provided.

Proceed

to STEP

3.

2.

Wall:

Locate

the

center

of the

two

holes

identified

in figure

1 as "HOLES

FOR

WALL.

Ddll

an angled

1/8"

(3 mm)

pilot

hole

in the

center

of each

hole

g.

as shown

in

figure

2. (A nail or awl may

be used

if

a drill is not available).

Secure

the

ANTI-TIP

bracket

to the

wall

with

the

two screws

provided

as shown

in

figure

2. Proceed

to STEP

3.

Cement

or Concrete

Construction:

1.

Suitable

screws

for concrete

construction

can

be

obtained

at a hardware

store.

Drill

the

required

size

hole

for the

screws

obtained

into

the

concrete

at the

center

of the

holes

identified

in

figure

1 as "HOLES

FOR

FLOOR".

Secure

the

ANTI-TIP

bracket

to the floor.

Proceed

to STEP

3.

STEP 3

-

Range Installation

A.

A free-standing

range may be

installed

by one

person.

g.

Align

the

range

to its designated

location

and slide

it

back

into position.

Note:

A minimum

clearance

of 1/4"

(6 mm)

is required

between

the

range

and the

leveling

foot that

will engage

the

ANTI-TIP

bracket,

see

figure

2.

C.

D.

E.

CAUTION:

Damage

to the

range

may

occur

if

range

is

moved

or lifted

by grasping

the

main

top or

backguard.

For

SAFETY

CONSIDERATIONS

as well

as optimum

performance

adjust

the

range

so that

it

is level.

This

may

be checked

by placing

a spidt

level

or a large

pan of water

on the

cooktop

or the

oven

rack.

If an

adjustment

is required

pull the

range

forward,

tip the

range

and

rotate

the leveling

feet

as required.

To check

the

range

for proper

installation

of the

anti-tip

bracket:

Use

a flashlight

and look

underneath

the

bottom

of the

range

to see that

one of the

rear

leveling

feet

is

engaged

in the

bracket

slot.

Proceed

with

the

remainder

of the

installation

instructions

provided

with

the

range.

FIGURE

1

NOI

L

_! I ,_

MU!

,)

(z_'

,i_lht_

/

FIGURE

2

-4.

Maytag MGR4452BDB Installation Manual - Page 4

Anti-tip, Device, Installation, Instructions - manual

Page 4 highlights