Maytag MGR5775QDW Installation Manual - Page 4

Anti-tip, Device, Installation, Instructions - manual

Page 4 highlights

ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS NOTE: A risk of range tip over exists if the appliance is not installed in accordance with the installation instructions provided. The proper use of this device minimizes the risk of TIP-OVER. In using this device the consumer must still observe the safety precautions as stated in the USE and CARE MANUAL and avoid using the oven door and/or lower drawer as a step stool. Installation instructions are provided for wood and cement in either floor or wall. Any other type of construction may require special installation techniques as deemed necessary to provide adequate fastening of the ANTI-TIP bracket to the floor or wall. STEP 1 - Locating The Bracket (see figure 1) A. Determine where either the right or left rear "edge" of the range will be located and mark the floor or wall. B. Place the BRACKET 9/16" (14.5 mm) from the marked "EDGE" toward center of opening and against the back wall as shown in figure 1, with orientation hole against wall. C. Use the bracket as a template and mark the required holes, as shown in figure 1 for the type of construction you will be using. STEP 2 - Anti-Tip Bracket Installation A. Wood Construction: 1. Floor: Locate the center of the two holes identified in figure 1 as "HOLES FOR FLOOR". Drill a 1/8" (3 mm) pilot hole in the center of each hole (a nail or awl may be used if a drill is not available). Secure the ANTI-TIP bracket to the floor with the two screws provided. Proceed to STEP 3. 2. Wall: Locate the center of the two holes identified in figure 1 as "HOLES FOR WALL. Drill an angled 1/8" (3 mm) pilot hole in the center of each hole as shown in figure 2. (A nail or awl may be used if a drill is not available). Secure the ANTI-TIP bracket to the wall with the two screws provided as shown in figure 2. Proceed to STEP 3. B, Cement or Concrete Construction: 1. Suitable screws for concrete construction can be obtained at a hardware store. Drill the required size hole for the screws obtained into the concrete at the center of the holes identified in figure 1 as "HOLES FOR FLOOR". Secure the ANTI-TIP bracket to the floor. Proceed to STEP 3. STEP 3 - Range Installation A. For safety considerations as well as optimum performance, adjust the range so it is level and to desired height prior to installing in cabinet opening. NOTE: Cooktop MUST be flush or above countertop, Levelness may be checked by placing a spirit level or a large pan of water on the cooktop or oven rack. Adjust the range by tipping it forward or back and rotate the leveling feet as required. NOTE: A minimum clearance of 1/4" (6 mm) is required between the range and the leveling foot that will engage the anti-tip bracket, (see figure 2). CAUTION: Damage to the range may occur if range is moved or lifted by grasping the main top, backguard or door handles. B, Align the range to its designated location and prepare to slide it back into position. Connect gas line and plug in power cord to outlet following guidelines outlined in connecting the range and remainder of installation instructions. C, Slide range in place visually inspecting to verify that power cord and gas line are freely routed and contained within recessed area of back panel. D, To check the range for proper installation of the anti-tip bracket, use a flashlight and look underneath the bottom of the range to see that one of the rear leveling feet is engaged in the bracket slot. 9/16" / !'ORIENTATION HOLESFOR S WALL // / ATTACHANTI-TIP BRACKETWITH A MINIMUM OF TWO (2) LONG SCREWS TO THE WALL OR FLOOR. ANTPTIP S BRACKET - LEVELING FOOT NOTE: USE A MINIMUM OF (2) SCREWS TO INSTALL ANTI-TiP BRACKET TO THE WALL OR FLOOR SCREWS MUST ENTER WOOD OR METAL WALL PLATE ANTI-TIP BRACKET SCREW BRACKET SLIDE IN TO SECURE RANGE BOTTOM 7 OF RANGE FLOOR H(EACH SIDOER) FIGURE 1 AR1_ 92_5-11t -4- FIGURE 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7

ANTI-TIP
DEVICE
INSTALLATION
INSTRUCTIONS
NOTE:
A risk of range tip over exists if the appliance
is
not installed in accordance
with the installation
instructions
provided. The proper use of this device
minimizes
the risk of TIP-OVER.
In using this device the
consumer
must still observe
the safety precautions
as
stated in the USE and CARE MANUAL
and avoid using
the oven door and/or lower drawer as a step stool.
Installation
instructions
are provided for wood and cement
in either floor or wall. Any other type of construction
may
require special installation
techniques
as deemed
necessary
to provide adequate fastening
of the ANTI-TIP
bracket to the floor or wall.
STEP
1-
Locating
The Bracket
(see
figure
1)
A.
Determine where either the right or left rear "edge" of
the range will be located and mark the floor or wall.
B.
Place the BRACKET
9/16" (14.5 mm) from the
marked "EDGE" toward center of opening and against
the back wall as shown in figure 1, with orientation
hole against wall.
C.
Use the bracket as a template
and mark the required
holes, as shown in figure 1 for the type of construction
you will be using.
STEP 2
-
Anti-Tip
Bracket
Installation
A.
Wood Construction:
1.
Floor: Locate the center of the two holes identified
in figure 1 as "HOLES
FOR FLOOR".
Drill a 1/8"
(3 mm) pilot hole in the center of each hole (a nail
or awl may be used if a drill is not available).
Secure the ANTI-TIP
bracket to the floor with the
two screws provided.
Proceed to STEP 3.
2.
Wall: Locate the center of the two holes identified
in figure 1 as "HOLES
FOR WALL. Drill an angled
1/8" (3 mm) pilot hole in the center of each hole
as shown in figure 2. (A nail or awl may be used if
a drill is not available).
Secure the ANTI-TIP
bracket to the wall with the two screws provided
as shown in figure 2. Proceed to STEP 3.
B,
Cement or Concrete Construction:
1.
Suitable screws for concrete construction
can be
obtained at a hardware store. Drill the required
size hole for the screws obtained
into the
concrete at the center of the holes identified
in
figure 1 as "HOLES
FOR FLOOR". Secure the
ANTI-TIP
bracket to the floor. Proceed to STEP 3.
STEP 3
-
Range
Installation
A.
For safety considerations
as well as optimum
performance,
adjust the range so it is level and to
desired height prior to installing
in cabinet opening.
NOTE:
Cooktop
MUST be flush or above
countertop,
Levelness
may be checked
by placing a spirit level or
a large pan of water on the cooktop or oven rack.
Adjust the range by tipping it forward or back and
rotate the leveling feet as required.
NOTE: A minimum
clearance
of 1/4" (6 mm) is
required
between the range and the leveling foot that
will engage the anti-tip bracket,
(see figure 2).
CAUTION:
Damage to the range may occur if range
is moved or lifted by grasping the main top, backguard
or door handles.
B,
Align the range to its designated
location and prepare
to slide it back into position. Connect gas line and
plug in power cord to outlet following
guidelines
outlined in connecting
the range and remainder
of
installation
instructions.
C,
D,
Slide range in place visually
inspecting
to verify that
power cord and gas line are freely routed and
contained
within recessed area of back panel.
To check the range for proper installation
of the
anti-tip bracket, use a flashlight
and look underneath
the bottom of the range to see that one of the rear
leveling feet is engaged
in the bracket slot.
/
!'ORIENTATION
ATTACHANTI-TIP BRACKETWITH A
HOLESFOR
S
MINIMUM OF TWO (2) LONG SCREWS
WALL
//
TO THE WALL OR FLOOR.
/
ANTPTIP
S
BRACKET
9/16"
OF RANGE
H
OR
FLOOR
(EACHSIDE)
-
LEVELING
FOOT
FIGURE
1
NOTE:
USE
A MINIMUM
OF (2) SCREWS
TO INSTALL
ANTI-TiP
BRACKET
TO THE
WALL
OR FLOOR
ANTI-TIP
SCREWS
MUST
BRACKET
ENTER
WOOD
OR METAL
SCREW
BRACKET
SLIDE
IN
WALL
PLATE
TO
SECURE
AR1_
92_5-11t
FIGURE 2
RANGE
BOTTOM
7
-4-