Maytag MGS8880DS Dimension Guide - Page 1
Maytag MGS8880DS Manual
View all Maytag MGS8880DS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
30" (76.2 cm) Slide-in Gas Range PRODUCT MODEL NUMBERS MGS8880D GAS SUPPLY REQUIREMENTS Gas supply line: q Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ¹⁄₂" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system. NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape. Flexible metal appliance connector: q If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long 1.3 cm) or ³⁄₄" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line. PRODUCT DIMENSIONS This manual covers several models. Your model may appear different from the models depicted. Dimensions given are maximum dimensions across all models. B C A D q A ¹⁄₂" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator. q Do not kink or damage the flexible metal tubing when moving the range. q Must include a shutoff valve: The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range. B A E F A. 1 3.0 cm) height from cooktop to top of vent B. 29⁷⁄₈" (75.9 cm) C. Model/serial number plate (located behind the oven door on the top right-hand side of the oven frame) D. 36" (91.4 cm) height to top of cooktop edge with leveling legs screwed all the way in* E. 28 71.9 cm) max. depth from front of console to back of range. F. 28⁷⁄₈" (73.3 cm) max. depth from handle to back of range. IMPORTANT: Range must be level after installation. Follow the instructions in the "Level Range" section. Using the cooktop as a reference for leveling the range is not recommended. *Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs. C A. Gas supply line B. Shutoff valve "open" position C. To range Gas Pressure Regulator The gas pressure regulator supplied with this range must be used. The inlet pressure to the regulator should be as follows for proper operation: Natural gas: Minimum pressure: 5" WCP Maximum pressure: 14" WCP LP gas: Minimum pressure: 11" WCP Maximum pressure: 14" WCP Contact local gas supplier if you are not sure about the inlet pressure. Type of Gas Natural gas: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas. q This range is factory set for use with Natural gas. See "Gas Conversions" section. The model/serial rating plate located behind the control panel has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier. LP gas conversion: Conversion must be done by a qualified service technician. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See "Gas Conversions" section. †®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Page 1 of 2 Ref. W10665256B 9/14