Memorex DCR5000-P User Guide - Page 8

Installation

Get Memorex DCR5000-P - Disney Princess Clock Radio PDF manuals and user guides
UPC - 961613073907
View all Memorex DCR5000-P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

DCR5000.O/M.QXD 1/28/03 7:21 AM Page 7 INSTALLATION Unravel the AC cord and connect it to a conveniently located AC outlet having 120V and 60Hz only. The Clock Display will illuminate and "0:00" or "12:00" will blink in AC Outlet the window. NOTE: If the AC plug does not fit into a AC Plug nonpolarized outlet, do not file or cut the wide blade. It is the user's responsibility to have an electrician replace the obsolete outlet. If the AC cord is disconnected or if there is a power failure, this electronic clock is designed to continue operating internally (without showing the time on the Clock Display) with two (2) AAA size batteries (not included). To install the batteries: • Remove the battery compartment door by inserting a small screwdriver, paper clip or similar item into the tab Ð+ Ð+ while gently pushing to remove. • Insert two (2) AAA size batteries into the battery compartment. Be sure to observe the polarity markings which are engraved inside the battery compartment. If the batteries are inserted incorrectly, the unit will not operate. • Replace the battery compartment door. Be sure to check the condition of the batteries periodically by disconnecting the AC cord and connecting it again two or three minutes later. The preset times should continue operating. If the present time does not appear, it indicates the battery is dead or not connected properly. BATTERY PRECAUTIONS Follow these precautions when using batteries in this device: 1. Use only the size and type of batteries specified. 2. Be sure to follow the correct polarity when installing the batteries as indicated next to the battery compartment. Reversed batteries may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer's directions.) 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
7
INSTALLATION
Unravel the AC cord and connect it to a
conveniently located AC outlet having 120V
and 60Hz only. The Clock Display will
illuminate and “0:00” or “12:00” will blink in
the window.
NOTE:
If the AC plug does not fit into a
nonpolarized outlet, do not file or cut the
wide blade. It is the user’s responsibility to have an electrician replace the
obsolete outlet.
If the AC cord is disconnected or if there is a power failure, this electronic
clock is designed to continue operating internally (without showing the time
on the Clock Display) with two (2) AAA size batteries (not included).
To install the batteries:
•
Remove the battery compartment door by inserting a
small screwdriver, paper clip or similar item into the tab
while gently pushing to remove.
•
Insert two (2) AAA size batteries into the battery
compartment. Be sure to observe the polarity markings
which are engraved inside the battery compartment. If the
batteries are inserted incorrectly, the unit will not operate.
•
Replace the battery compartment door.
Be sure to check the condition of the batteries periodically by disconnecting
the AC cord and connecting it again two or three minutes later. The preset
times should continue operating. If the present time does not appear, it
indicates the battery is dead or not connected properly.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1.
Use only the size and type of batteries speci
fi
ed.
2.
Be sure to follow the correct polarity when installing the batteries as indicated next
to the battery compartment. Reversed batteries may cause damage to the device.
3.
Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or
old batteries with fresh ones.
4.
If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
5.
Do not try to recharge batteries not intended to be recharged; they can overheat
and rupture. (Follow battery manufacturer’s directions.)
DCR5000.O/M.QXD
1/28/03
7:21 AM
Page 7