Metabo W 24-230 MVT Operating Instructions 2 - Page 16

en ENGLISH 5. Overview See page 2. 1 "Quick"clamping nut * 2 Support flange * 3 Spindle 4 WEA...: Autobalancer support flange (nondetachable) * 5 Spindle locking button 6 Electronic signal indicator * 7 Lock (to prevent the machine from being switched on unintentionally, or for continuous operation)* 8 Trigger (for switching on and off) 9 Button (to turn the main handle) 10 Main handle 11 Additional handle/Additional handle with vibration damping 12 Safety cover 13 Adjusting nut * 14 2-hole spanner * 15 Quick-release clamp (to adjust safety guard without the use of tools) 16 Screw (to adjust clamping force of quick- release clamp) * depending on equipment/not in scope of delivery 6. Commissioning Before plugging in, check that the rated mains voltage and mains frequency, as stated on the rating label, match with your power supply. Always install an RCD with a max. trip current of 30 mA upstream. Uofs1e.5onmlyme2x.teEnxsteionnsicoanbcleasbwleisthmaumstinc.ocrrroesssp-osnedcttioon the power consumption of the machine (cf Technical Specifications). If a cable roller is used, always roll up the cable completely. 6.1 Attaching the additional handle Always work with the additional handle (11) attached! Manually screw in the additional handle securely in the left, centre or right threaded hole (depending on requirements). 6.2 Attach the safety guard (for working with abrasive discs) Prior to operation: Attach safety guard. For reasons of safety, the safety guard (12) should always be attached when roughing work is performed. For reasons of safety, the special parting guard should always be attached before parting work is performed (see chapter 11. Accessories). See illustration E on page 2. 16 - Open quick-release clamp (15). Mount the safety guard (12) in the position indicated. - Turn the safety guard until the closed section is facing the operator. - Close quick-release clamp. - If necessary, increase clamping force of quick- release clamp by tightening the screw (16) (with opened quick-release clamp). Use only accessories that are covered by at least 3.4 mm by the safety guard. 6.3 Pivotable main handle Only work with the main handle (10) engaged. See illustration B on page 2. - Push in the button (9). - The main handle (10) can now be turned 90° to both sides and can be engaged. - Make sure that it is securely positioned: the main handle (10) must be engaged and it should not be possible to move it. 6.4 Power-supply connection The mains sockets must be protected using timedelay fuses or circuit breakers. Machines with "WE..." in the model designation: (with inbuilt automatic startup-current limitation(soft start).) The mains sockets can also be protected using fast-acting fuses or circuit breakers. 7. Attaching the grinding disc Prior to any conversion work: Pull the mains plug from the socket. The machine must be switched off and the spindle at a standstill. For reasons of safety, attach the parting guard before performing parting work (see chapter 11. Accessories). 7.1 Locking the spindle Press in the spindle locking button (5) only when the spindle is stationary! - Press in the spindle locking button (5) and turn the spindle (3) by hand until the spindle locking button engages. 7.2 Placing the grinding wheel in position See illustration C on page 2. Machines with the designation W 2..., WE 2...: - Fit the support flange (2) on the spindle. The flange should not turn on the spindle when properly attached. - Position the grinding wheel on the support flange (2) as shown in illustration C. The grinding disc must lay flat on the supporting flange. Machines with the designation WEA 2...: The Autobalancer support flange (4) is permanently fitted on the spindle. As is the case with most other angle grinders, a detachable support flange is not necessary.