Metabo WEP 19-150 Q M-Brush Operating Instructions - Page 15

Emission values, Wear ear protectors

Get Metabo WEP 19-150 Q M-Brush PDF manuals and user guides View all Metabo WEP 19-150 Q M-Brush manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

tmax,2 = max. permitted thickness of clamping shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. permitted thickness of accessory M = spindle thread l = length of the grinding spindle n* = no-load speed (maximum speed) Inm1V2*0 V = no-load speed (adjustable) = Current at 120 V = weight without mains cable * Machines with the designation WE... : Energy-rich, high-frequency interference can cause fluctuations in speed. The fluctuations disappear, however, as soon as the interference fades away. The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards). Emission values These values make it possible to assess the emissions from the power tool and to compare different power tools. Depending on the operating conditions, the condition of the power tool or the accessories, the actual load may be higher or lower. For assessment purposes, please allow for breaks and periods when the load is lower. Based on the adjusted estimates, arrange protective measures for the user e.g. organisational measures. Vibration total value (vector sum of three directions) determined in accordance with EN 60745: ah, SG = Vibration emission value (surface grinding) ah, DS = Vibration emission value (sanding with sanding plate) ah, P = Vibration emission value (polishing) Kh,SG/DS/P = Uncertainty (vibration) Wear ear protectors! ENGLISH en 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
ENGLISH
en
15
t
max,2
=
max. permitted thickness of clamping
shank on accessory when using
"Quick" clamping nut (1)
t
max,3
=
roughing disc/cutting disc:
max. permitted thickness of accessory
M
=
spindle thread
l
=
length of the grinding spindle
n*
=
no-load speed (maximum speed)
n
V
*
=
no-load speed (adjustable)
I
120 V
=
Current at 120 V
m
=
weight without mains cable
* Machines with the designation WE... : Energy-rich,
high-frequency interference can cause fluctuations
in speed. The fluctuations disappear, however, as
soon as the interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, SG
=
Vibration emission value
(surface grinding)
a
h, DS
=
Vibration emission value
(sanding with sanding plate)
a
h, P
=
Vibration emission value
(polishing)
K
h,SG/DS/P
= Uncertainty (vibration)
Wear ear protectors!