Milwaukee Tool M12 Multi-Tool Tool Only Service Parts List - Page 1

SERVICE PARTS LIST BULLETIN NO. 54-22-2400 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12 VOLT MULTI-TOOL 00 0 EXAMPLE: CATALOG NO. Component Parts (Small #) Are Included When Ordering The Assembly (Large #). 2426-20 STARTING SERIAL NO. 28 29 C73A REVISED BULLETIN DATE Oct. 2021 WIRING INSTRUCTION See Reverse Side Install spring clip (35) into the left housing halve (28) prior to installing right housing halve (3). NOTE: Right 28 spring interlock must match that of the left housing halve prior to 35 tightening housing screws (1 and 4). 3 Interlock Area 30 32 33 35 54 5 6 60 37 NOTE: Production of this model did not have 3 Dust Cap (60) on the rear of the motor prior to March 2016. It is recommended when servicing this tool, to order and install a new Dust Cap (43-44- 1500) on all early models. 4(1x) 2 1(9x) 44 52 30 32 31 33 5 6 17 9 56 8 11 9 7 10 55 1 34 3 37 4 38 28 38 11 57 7 14 10 15 12 36 13 8 12 13 53 16 21 18 22 19 23 20 24 14 15 16 36 18 20 19 FIG. PART NO. 1 06-82-1080 2 12-20-2426 3 4 06-82-2395 5 6 7 8 9 10 34-40-0620 11 12 13 14 15 16 17 06-65-0085 18 19 20 21 22 23 24 25 42-04-0730 26 42-92-1150 27 05-81-1400 28 29 45-72-0250 30 31 32 33 34 35 42-70-0480 36 37 44-52-1015 38 44-52-1010 40 42-52-0475 41 05-74-0900 44 42-55-2426 52 23-66-0915 53 14-29-0675 54 14-50-1020 55 31-44-2570 DESCRIPTION OF PART NO. REQ. M3.0 x 14mm Pan Hd. ST T-10 Screw (11) Service Nameplate (1) Housing Halve - Right (1) M2.6 x 10mm Pan Hd. ST T-9 Screw (1) Motor (1) Motor Pinion (1) Mounting Plate (1) M3.0 x 16mm Pan Hd. Screw (2) Washer (2) O-Ring (2) Spring Washer (2) Spline Shaft (1) Counter Balance (1) Ball Bearing (1) Retaining Ring (1) Needle Roller Bearing (1) Pin (2) Gearcase (1) Needle Bearing (1) Fork (1) Ball Bearing (1) Retaining Ring (1) Output Shaft (1) Bit Holder (1) Adapter (Accessory-Sold Separately) (1) Blade Cover (1) M6 x 1 x 22.6 Flat Hd. Hex Recess Screw (1) Housing Halve - Left (1) Switch Trigger (1) Switch (1) Leadwire Assembly - Red (Not Shown) (1) Contact Plate Holder (1) PCBA (1) Fuel Gauge Label (Not Shown) (1) Spring Clip (1) Ball Bearing (1) Rubber Pad - Right (1) Rubber Pad - Left (1) Gearcase Cover (1) M3.0 x 10mm Pan Hd. T-10 Screw (2) Canvas Carrying Case (1) Switch Assembly Kit (1) Gearcase Assembly Kit (1) Motor Assembly Kit (1) Housing Halve Assembly Kit (1) LUBRICATION NOTES: Use Type 'J' Grease, 1 No. 49-08-4220 When servicing, remove 90-95% 21 of the existing grease prior to in- stalling Type "J". Original grease maybe similar in color but not 22 compatible with "J". Apply a heavy coating of grease 23 to Motor Pinion (6) and Spline Shaft (12). Approx. 0.5g 24 Place a heavy coating of grease in and around the open Ball Bearing (36). Approx. 1g 25 Fill back cavity of Gearcase (18) 26 with approx. 3.5g of grease. Total of 5.0g (.17oz.) 27 40 41 ACCESSORIES BACKING PAD 44-52-2000 PLUNGE CUT WOOD BLADE 50-02-1025 FIG. PART NO. 56 14-46-2426 57 42-87-0200 60 43-44-1500 49-96-0500 10-20-2426 DESCRIPTION OF PART Screw and Washer Kit Counter Balance Assembly Kit Dust Cap Hex Key (Not Shown) Warning Label (Not Shown) NO. REQ. (1) (1) (1) (1) (1) FIG. NOTES 1,4 Hand tighten housing screws to prevent over tightening. Exercise caution when tightening screws if a cordless driver drill is used. 5,8 Apply Blue Loctite® 242 or equivalent, sparingly to the first two or three threads of screws (8) prior to assembling to motor (5). MILWAUKEE TOOL • www.milwaukeetool.com 13135 W. Lisbon Road, Brookfield, WI 53005 Drwg. 6