Home » Motorola Manuals » Bridges & Routers » Motorola 3356 » Manual Viewer

Motorola 3356 Software User Guide - Page 247

DMT Settings, set dmt wiringMode [ auto | tip_ring | A_A1 ]

Add to My Manuals
Save this manual to your list of manuals

Page 247 highlights

CONFIG Commands DMT Settings DSL Commands set dmt type [ lite | dmt | ansi | multi | adsl2 | adsl2+ | readsl2 | adsl2anxm | adsl2+anxm ] Selects the type of Discrete Multitone (DMT) asynchronous digital subscriber line (ADSL) protocol to use for the WAN interface. Beginning with Firmware Version 7.6, the type value also supports the following settings on certain model units: adsl2, adsl2+, readsl2, adsl2anxm, adsl2+anxm. ☛ NOTE: Some dmt type settings are now supported for many Annex B (335xN) platforms. 2200 Series and 33xxN Series models are supported. Currently, adsl2anxm and adsl2+anxm are not supported in Annex B. set dmt autoConfig [ off | on ] Enables support for automatic VPI/VCI detection and configuration. When set to on (the default), a pre-defined list of VPI/VCI pairs are searched to find a valid configuration for your ADSL line. Entering a value for the VPI or VCI setting will disable this feature. set dmt wiringMode [ auto | tip_ring | A_A1 ] (not supported on all models) This command configures the wiring mode setting for your ADSL line. Selecting auto (the default) causes the Gateway to detect which pair of wires (inner or outer pair) are in use on your phone line. Specifying tip_ring forces the inner pair to be used; and A_A1 the outer pair. set dmt metallic-termination [ auto | disabled | always_on ] (not supported on all models) Beginning with firmware version 7.5.2, this command allows you to apply a sealing current to "dry" DSL lines so that the wiring doesn't corrode. 247

Section	Page
Copyright	2
Table of Contents	3
CHAPTER 1 Introduction	13
What’s New in 7.6	13
About Netopia Documentation	14
Intended Audience	14
Documentation Conventions	15
General	15
Internal Web Interface	15
Command Line Interface	15
Organization	17
A Word About Example Screens	17
CHAPTER 2 Basic Mode Setup	19
Important Safety Instructions	20
POWER SUPPLY INSTALLATION	20
TELECOMMUNICATION INSTALLATION	20
Wichtige Sicherheitshinweise	21
NETZTEIL INSTALLIEREN	21
INSTALLATION DER TELEKOMMUNIKATION	21
Setting up the Netopia Gateway	22
Configuring the Netopia Gateway	26
MiAVo VDSL and Ethernet WAN models Quickstart	27
PPPoE Quickstart	28
Netopia Gateway Status Indicator Lights	30
Home Page - Basic Mode	31
Link: Manage My Account	33
Link: Status Details	34
Link: Enable Remote Management	35
Link: Expert Mode	36
Link: Update Firmware	37
Link: Factory Reset	38
CHAPTER 3 Expert Mode	39
Accessing the Expert Web Interface	39
Open the Web Connection	39
Home Page - Expert Mode	41
Home Page - Information	42
Toolbar	44
Navigating the Web Interface	44
Link: Breadcrumb Trail	44
Restart	45
Button: Restart	45
Link: Alert Symbol	46
Help	47
Button: Help	47
Configure	48
Button: Configure	48
Link: Quickstart	48
Link: LAN	50
Wireless	53
Privacy	54
Advanced	57
Multiple SSIDs	62
Wireless MAC Authorization	63
Link: WAN	68
Link: Advanced	72
Link: IP Static Routes	73
Link: IP Static ARP	75
Link: Pinholes	75
Link: IPMaps	82
Configure the IPMaps Feature	83
Link: Default Server	85
Link: Differentiated Services	89
Link: DNS	92
Link: DHCP Server	92
Link: RADIUS Server	94
Link: SNMP	95
Link: IGMP (Internet Group Management Protocol)	97
Link: UPnP	100
Link: LAN Management	101
Link: Advanced -> Ethernet Bridge	102
Configuring for Bridge Mode	103
Link: VLAN	106
Link: System	111
Link: Syslog Parameters	111
Log Event Messages	113
Link: Internal Servers	116
Link: Software Hosting	116
Rename a User(PC)	119
Link: Clear Options	120
Link: Time Zone	121
Security	122
Button: Security	122
Link: Passwords	123
Link: Firewall	125
Link: IPSec	130
SafeHarbour IPSec VPN	131
Link: Stateful Inspection	140
Stateful Inspection Firewall installation procedure	140
Exposed Addresses	141
Stateful Inspection Options	144
Open Ports in Default Stateful Inspection Installation	145
Firewall Tutorial	146
General firewall terms	146
Basic IP packet components	146
Basic protocol types	147
Firewall design rules	148
Filter basics	151
Example filters	152
Link: Packet Filter	154
What’s a filter and what’s a filter set?	155
How filter sets work	155
How individual filters work	156
Design guidelines	163
Working with IP Filters and Filter Sets	164
Adding a filter set	164
Adding filters to a filter set	165
Deleting a filter set	170
Associating a Filter Set with an Interface	171
Policy-based Routing using Filtersets	173
TOS field matching	173
Link: Security Log	176
Install	179
Button: Install	179
Link: Install Software	180
Step 1: Required Files	181
Step 2: Netopia firmware Image File	181
Link: Install Keys	184
Use Netopia Software Feature Keys	184
Link: Install Certificate	188
CHAPTER 4 Basic Troubleshooting	191
Status Indicator Lights	192
LED Function Summary Matrix	201
Factory Reset Switch	203
CHAPTER 5 Advanced Troubleshooting	205
Home Page	206
Button: Troubleshoot	208
Expert Mode	208
Link: System Status	209
Link: Ports: Ethernet	210
Link: Ports: DSL	211
Link: IP: Interfaces	212
Link: DSL: Circuit Configuration	213
Link: System Log: Entire	214
Link: Diagnostics	215
Link: Network Tools	216
CHAPTER 6 Command Line Interface	221
Overview	222
Starting and Ending a CLI Session	224
Logging In	224
Ending a CLI Session	224
Saving Settings	225
Using the CLI Help Facility	225
About SHELL Commands	225
SHELL Prompt	225
SHELL Command Shortcuts	225
SHELL Commands	226
Common Commands	226
WAN Commands	236
About CONFIG Commands	237
CONFIG Mode Prompt	237
Navigating the CONFIG Hierarchy	237
Entering Commands in CONFIG Mode	239
Guidelines: CONFIG Commands	240
Displaying Current Gateway Settings	240
Step Mode: A CLI Configuration Technique	240
Validating Your Configuration	241
CONFIG Commands	242
DSL Commands	242
Bridging Settings	244
DHCP Settings	245
DMT Settings	247
Domain Name System Settings	248
IGMP Settings	249
IP Settings	250
IPMaps Settings	262
Network Address Translation (NAT) Default Settings	262
Network Address Translation (NAT) Pinhole Settings	263
PPPoE /PPPoA Settings	264
Ethernet Port Settings	267
Command Line Interface Preference Settings	267
Port Renumbering Settings	269
Security Settings	270
SNMP Settings	282
System Settings	283
Syslog	288
Wireless Settings (supported models)	290
VDSL Settings	302
CHAPTER 7 Glossary	311
CHAPTER 8 Technical Specifications and Safety Information	327
Description	327
Power requirements	327
Environment	327
Software and protocols	328
Agency approvals	329
Regulatory notices	329
Manufacturer’s Declaration of Conformance	330
Important Safety Instructions	332
47 CFR Part 68 Information	333
FCC Requirements	333
FCC Statements	333
Electrical Safety Advisory	334
CHAPTER 9 Overview of Major Capabilities	335
Wide Area Network Termination	336
PPPoE/PPPoA (Point-to-Point Protocol over Ethernet/ATM)	336
Instant-On PPP	336
Simplified Local Area Network Setup	337
DHCP (Dynamic Host Configuration Protocol) Server	337
DNS Proxy	337
Management	338
Embedded Web Server	338
Security	339
Remote Access Control	339