Home » Motorola Manuals » Bridges & Routers » Motorola 3386-ENT » Manual Viewer

Motorola 3386-ENT Administration Guide - Page 229

VoIP settings (supported models), server_name, ip_address

Add to My Manuals
Save this manual to your list of manuals

Page 229 highlights

VoIP settings (supported models) Voice-over-IP (VoIP) refers to the ability to make voice telephone calls over the Internet. This differs from traditional phone calls that use the Public Switched Telephone Network (PSTN). VoIP calls use an Internet protocol, Session Initiation Protocol (SIP), to transmit sound over a network or the Internet in the form of data packets. Certain Motorola Netopia® Gateway models have two separate voice ports for connecting telephone handsets. These models support VoIP. If your Gateway is a VoIP model, you can configure the VoIP features. set ip client voip ip-interface [ no-restrict | ip-dsl-vcc1... | ppp-vcc2... | ppp-enet-x... | ip-enet-x... ] This command allows you to specify which WAN IP interface to use for VoIP traffic. The option list will display the WAN IP interface name if the interface is enabled. K no-restrict: default behavior - use the default (first WAN IP) interface. K ip-dsl-vcc1, 2, 3: will show IP WAN interface. K ppp-vcc1, 2, 3: will show IP PPP WAN interface. K ip-enet-x: will show IP over Ethernet over VDSL/Ethernet WAN. K ppp-enet-x: will show PPP over Ethernet over VDSL/Ethernet WAN. set voip phone [ 1 | 2 ] sip-option [ off | on ] Turns SIP on or off for the specified phone. Default is off. set voip phone [ 1 | 2 ] sip-proxy-server [ server_name | ip_address ] Specifies the SIP proxy server for the specified phone by fully qualified server name or IP address. set voip phone [ 1 | 2 ] sip-proxy-server-transport [ UDP | TCP | TLS ] Specifies the SIP proxy server transport protocol for the specified phone. Default is UDP. set voip phone [ 1 | 2 ] sip-registrar-setting sip-registrar-server [ server_name | ip_address ] Specifies the SIP registration server for the specified phone by fully qualified server name or IP address. set voip phone [ 1 | 2 ] sip-registrar-setting sip-registrar-server-transport [ UDP | TCP | TLS ] Specifies the SIP registration server transport protocol for the specified phone. Default is UDP. set voip phone [ 1 | 2 ] sip-registrar-setting sip-expires-time [ 0 - 65535 ] Specifies the SIP registration server time-out duration from 0 - 65535 seconds for the specified phone. Default is 3600 (1 hour). 229

Section	Page
Table of Contents	3
CHAPTER 1 Setting up Your Motorola Netopia® Gateway	7
What’s New in 7.8.2	8
Important Safety Instructions	9
POWER SUPPLY INSTALLATION	9
TELECOMMUNICATION INSTALLATION	9
PRODUCT VENTILATION	9
Wichtige Sicherheitshinweise	10
NETZTEIL INSTALLIEREN	10
INSTALLATION DER TELEKOMMUNIKATION	10
Set up your Gateway	11
Configure Your PC for Dynamic Addressing	12
Motorola Netopia® Gateway Quickstart	15
CHAPTER 2 Basic Mode Features	19
The Home Page	20
Home Page Information	20
Links Bar	22
Firewall	23
Firewall Background	23
Wireless Protected Setup	26
Wireless	28
Enable Wireless	28
Wireless ID (SSID)	28
Enable Wireless Protected Setup (WPS)	28
Enable Wireless Scheduler	29
Enable Wireless Protected Setup (WPS)	29
Privacy	29
Advanced Configuration Options (optional)	30
WiFi Multimedia	42
Wireless MAC Authorization (optional)	44
Gaming	46
Expert Mode	51
Troubleshoot	52
Diagnostics	53
Statistics	54
DSL	54
ATM	55
Ethernet	55
IP	55
LAN	55
Wireless	56
Logs	56
Help	57
CHAPTER 3 Expert Mode	59
Home Page - Expert Mode	60
Home Page Information	60
Help	62
Links Bar	63
Configure	64
Connection	65
LAN/WAN	67
DHCP Server	68
IP Passthrough	70
NAT	71
Router Password	76
Time Zone	77
VLAN	78
Overview	78
Ethernet Switching/Policy Setup	79
VoIP	85
Wireless	89
Enable Wireless	89
Wireless ID (SSID)	89
Enable Wireless Scheduler	90
Enable Wireless Protected Setup (WPS)	90
Privacy	90
Advanced Configuration Options (optional)	91
WiFi Multimedia	102
Wireless MAC Authorization (optional)	104
Statistics	106
DSL	106
ATM	106
Ethernet	107
IP	107
LAN	107
Wireless	108
Logs	108
Diagnostics	109
Remote Access	110
Update Router	111
• From a Server	111
• From your PC	111
Reset Router	112
Restart Router	113
Basic Mode	114
CHAPTER 4 Basic Troubleshooting	115
Status Indicator Lights	116
LED Function Summary Matrix	124
Factory Reset Switch	126
CHAPTER 5 Command Line Interface	127
Overview	129
Starting and Ending a CLI Session	131
Logging In	131
Ending a CLI Session	131
Saving Settings	131
Using the CLI Help Facility	131
About SHELL Commands	132
SHELL Prompt	132
SHELL Command Shortcuts	132
SHELL Commands	133
Common Commands	133
WAN Commands	144
About CONFIG Commands	145
CONFIG Mode Prompt	145
Navigating the CONFIG Hierarchy	145
Entering Commands in CONFIG Mode	146
Guidelines: CONFIG Commands	146
Displaying Current Gateway Settings	146
Step Mode: A CLI Configuration Technique	147
Validating Your Configuration	147
CONFIG Commands	148
Remote ATA Configuration Commands	148
DSL Commands	150
Bridging Settings	151
DHCP Settings	153
DMT Settings	159
Domain Name System Settings	160
IGMP Settings	162
IP Settings	164
Queue Configuration	177
IPMaps Settings	184
Network Address Translation (NAT) Default Settings	185
Network Address Translation (NAT) Pinhole Settings	186
PPPoE /PPPoA Settings	187
PPPoE with IPoE Settings	190
Ethernet Port Settings	191
802.3ah Ethernet OAM Settings	192
Command Line Interface Preference Settings	193
Port Renumbering Settings	194
Security Settings	195
SNMP Settings	209
System Settings	210
Syslog	214
Wireless Settings (supported models)	216
VLAN Settings	224
VoIP settings (supported models)	229
UPnP settings	235
DSL Forum settings	235
Remote Management settings	237
Backup IP Gateway Settings	238
VDSL Settings	240
CHAPTER 6 Technical Specifications and Safety Information	247
Description	247
Power requirements	247
Environment	247
Software and protocols	247
Agency approvals	248
Regulatory notices	248
Manufacturer’s Declaration of Conformance	249
Important Safety Instructions	250
47 CFR Part 68 Information	251
FCC Requirements	251
FCC Statements	251
Electrical Safety Advisory	252
Warranty Information	252
Software License, Limited Warranty and Limitation of Remedies	252
Software License	252
Limited Warranty	253
General Provisions	253
Copyright Acknowledgments	254
Caring for the Environment by Recycling	256
Beskyttelse af miljøet med genbrug	256
Umweltschutz durch Recycling	256
Cuidar el medio ambiente mediante el reciclaje	256
Recyclage pour le respect de l'environnement	256
Milieubewust recycleren	257
Dba¸oÊç o Êrodowisko - recykling	257
Cuidando do meio ambiente através da reciclagem	257
Var rädd om miljön genom återvinning	257

Match case Limit results 1 per page

229

VoIP settings (supported models)

Voice-over-IP (VoIP) refers to the ability to make voice telephone calls over the Internet. This differs from

traditional phone calls that use the Public Switched Telephone Network (PSTN). VoIP calls use an Inter-

net protocol, Session Initiation Protocol (SIP), to transmit sound over a network or the Internet in the

form of data packets. Certain Motorola Netopia

Gateway models have two separate voice ports for

connecting telephone handsets. These models support VoIP. If your Gateway is a VoIP model, you can

conﬁgure the VoIP features.

set ip client voip ip-interface

[ no-restrict | ip-dsl-vcc1... | ppp-vcc2... | ppp-enet-x... | ip-enet-x... ]

This command allows you to specify which WAN IP interface to use for VoIP trafﬁc. The option list will

display the WAN IP interface name if the interface is enabled.

❑

no-restrict

: default behavior — use the default (ﬁrst WAN IP) interface.

❑

ip-dsl-vcc1, 2, 3

: will show IP WAN interface.

❑

ppp-vcc1, 2, 3

: will show IP PPP WAN interface.

❑

ip-enet-x

: will show IP over Ethernet over VDSL/Ethernet WAN.

❑

ppp-enet-x

: will show PPP over Ethernet over VDSL/Ethernet WAN.

set voip phone [ 1 | 2 ] sip-option [ off | on ]

Turns SIP on or off for the speciﬁed phone. Default is

off

set voip phone [ 1 | 2 ] sip-proxy-server [

server_name

ip_address

]

Specifies the SIP proxy server for the specified phone by fully qualified server name or IP address.

set voip phone [ 1 | 2 ] sip-proxy-server-transport [ UDP | TCP | TLS ]

Speciﬁes the SIP proxy server transport protocol for the speciﬁed phone. Default is

UDP

set voip phone [ 1 | 2 ] sip-registrar-setting sip-registrar-server

[

server_name

ip_address

]

Specifies the SIP registration server for the specified phone by fully qualified server name or IP

address.

set voip phone [ 1 | 2 ] sip-registrar-setting

sip-registrar-server-transport [ UDP | TCP | TLS ]

Speciﬁes the SIP registration server transport protocol for the speciﬁed phone. Default is

UDP

set voip phone [ 1 | 2 ] sip-registrar-setting sip-expires-time [ 0 - 65535 ]

Speciﬁes the SIP registration server time-out duration from 0 – 65535 seconds for the speciﬁed phone.

Default is

3600

(1 hour).