Motorola H300 User Manual - Page 2
Turning On And Off, Wearing The, Headset, Changing For Use, On Other Ear, Changing Volume, Button
UPC - 723755890107
View all Motorola H300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
H300 Bluetooth® Handsfree Headset IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H300. TURNING ON AND OFF To turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off. To conserve battery power, turn off your headset when you don't plan to use it for a while. WEARING THE HEADSET 1 Open the earhook. 2 Loop the earhook over your ear. 3 Press the headset to your ear. Call Button CHANGING FOR USE ON OTHER EAR You can wear your H300 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear: 1 Open the earhook 90 degrees from the headset. 2 Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. 3 Flip the headset over. 4 Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. 1 Open Earhook 2 Pull Earhook Up 040059o Hinge Pin CHANGING VOLUME BUTTON ORIENTATION If you change your headset to wear on the other ear, you can also change the orientation of the Volume buttons. 1 Turn the headset power off. 2 Press the Call button and the Volume button you want to assign as the "volume up" button until the blue indicator light flashes twice. The headset power turns on. Call Button Volume Buttons FOR MORE INFORMATION ON USING YOUR MOTOROLA H300 Visit us at www.hellomoto.com/bluetooth and click Support. SUPPORT If you need more help, contact us at 1-877-MOTOBLU. MAKING CALLS Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) Note: Your H300 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information. MAKING CALLS CONTINUED Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons Note: Some features are phone/network dependent. INDICATOR LIGHTS The indicator lights provide information about your headset status. Indicator Light Headset Status Off Power off On (steady) Pairing mode 10 rapid flashes Pairing successful Slow pulse Connected (on a call) Quick flash Standby (not on call) Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode. AUDIO TONES The audio tones provide information about your headset status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 60 sec. No audio indications; deteriorating quality Ring tone Single high tone Single low tone Dual high/low tone Single high tone Low to high tone Two ascending tones Two descending tones Headset Status Volume at minimum or maximum Low battery Out of range Incoming call Pairing confirmation Voice activation Voice tag not recognized End call Phone network not available Mute enabled Mute disabled