Motorola MR350R User Guide - Page 1

MR350/351

KEM-PK14190-90

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general safety

information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control your

exposure and ensure compliance with the general population/

uncontrolled environment exposure limits, always adhere to the following

procedure:

•

Transmit no more than 50% of the time.

•

To receive calls, release the PTT button.

•

To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio

generates measurable RF energy exposure only when transmitting (in

terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy

exposure standards and guidelines:

•

United States Federal Communications Commission, Code of Federal

Regulations; 47CFR part 2 sub-part J.

•

American National Standards Institute (ANSI)/Institute of Electrical

and Electronic Engineers (IEEE) C95. 1-1992.

•

Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

•

International Commission on Non-Ionizing Radiation Protection

(ICNIRP) 1998.

•

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure

to Radiofrequency Electromagnetic Fields in the Frequency Range

from 3 KHz to 300 GHz, 1999.

•

Australian Communications Authority Radiocommunications

(Electromagnetic Radiation—Human Exposure) Standard, 2003.

•

ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of

limitation of exposure to electrical, magnetic and electromagnetic fields

in the radio frequency range between 9 KHz and 300GHz”.

To ensure optimal radio performance and make sure human exposure to

radio frequency electromagnetic energy is within the guidelines set forth

in the above standards, always adhere to the following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could damage the

radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding the

antenna affects its effective range.

Body-Worn Operation

To maintain compliances with FCC/Health Canada RF exposure

guidelines if you wear a radio on your body when transmitting always

place the radio in a Motorola-supplied or approved clip holder, holster,

case or body harness for this product. Use of non-Motorola-approved

accessories may exceed FCC/Health Canada RF exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-worn

accessories and are not using the radio held in the normal use position,

ensure the radio and its antenna are at least 1 inch (2.5 cm) from your

body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or without an

accessory cable,

position the radio and its antenna at least one inch

(2.5 cm) from the body.

Approved Accessories

For a list of approved Motorola accessories, visit our Web site at

www.motorola.com.

Electromagnetic Interference/Compatibility

Note:

Nearly every electronic device is susceptible to electromagnetic

interference (EMI) if inadequately shielded, designed or otherwise

configured for electromagnetic compatibility. This device complies with

Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1.

This device may not cause harmful interference; and

2.

This device must accept any interference received, including

interference that may cause undesired operation.

IC Canada

The term "IC:" before the equipment certification number only signifies

that the Industry Canada technical specifications were met.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts, turn

off your radio in any facility where posted notices instruct you to do so.

Hospitals or health care facilities may be using equipment that is

sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an aircraft.

Any use of a radio must be in accordance with applicable regulations

per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends that a

minimum separation of 6 inches (15 cm) be maintained between a

handheld wireless radio and a pacemaker. These recommendations are

consistent with the independent research by and recommendations of

the U.S. Food and Drug Administration.

People with pacemakers should:

•

ALWAYS keep the radio more than 6 inches (15 cm) from their

pacemaker when the radio is turned ON.

•

Not carry the radio in the breast pocket.

•

Use the ear opposite the pacemaker to minimize the potential for

interference.

•

Turn the radio OFF immediately if there is any reason to suspect that

interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing aids. In the

event of such interference, you may want to consult your hearing aid

manufacturer to discuss alternatives.

Medical Devices – Other

If you use any other personal medical device, consult the manufacturer

of your device to determine if it is adequately shielded from RF energy.

Your physician may be able to assist you in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the area

where you drive, and always obey them. If you do use your radio while

driving, please:

•

Give full attention to driving and to the road.

•

Use hands-free operation, if available.

•

Pull off the road and park before making or answering a call if driving

conditions so require.

The use of a two-way radio while engaged in activities requiring

concentration may cause distraction or otherwise impair your ability to

safely participate in such activities. Always use technology safely.

Do not place a portable radio in the area over an air bag or in the air bag

deployment area. Air bags inflate with great force. If a portable radio is

placed in the air bag deployment area and the air bag inflates, the radio

may be propelled with great force and cause serious injury to occupants

of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially explosive

atmosphere. Only radio types that are especially qualified should be

used in such areas as “Intrinsically Safe.” Do not remove, install or

charge batteries in such areas. Sparks in a potentially explosive

atmosphere can cause an explosion or fire resulting in bodily injury or

even death.

For More Information

For further information, you may call Motorola at 1-800-638-5119 (U.S.

and Canada), or e-mail us at [email protected] or visit us on the

Internet at www.motorola.com.

Note:

The areas with potentially explosive atmospheres referred to above

include fueling areas such as below decks on boats, fuel or chemical

transfer or storage facilities, areas where the air contains chemicals or

particles (such as grain, dust or metal powders) and any other area

where you would normally be advised to turn off your vehicle engine.

Areas with potentially explosive atmospheres are often—but not

always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your

radio when you are near electrical blasting caps, in a blasting area, or in

areas posted “Turn off two-way radios.” Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna.

If a

damaged antenna comes into contact with your skin, a minor burn can

result.

Batteries

All batteries can cause property damage and/or bodily injury such as burns

if a conductive material—like jewelry, keys or beaded chains— touch

exposed terminals. The conductive material may complete an electrical

circuit (short circuit) and become quite hot. Exercise care in handling any

charged battery, particularly when placing it inside a pocket, purse or other

container with metal objects.

Exercise care when removing NiMH or AA batteries. Do not use sharp or

conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1.

Do not expose the charger to rain or snow.

2.

Do not operate or disassemble the charger if it has received a sharp

blow, or has been dropped or damaged in any way.

3.

Never alter the AC cord or plug provided with the unit. If the plug will

not fit the outlet, have the proper outlet installed by a qualified

electrician. An improper condition can result in a risk of electric

shock.

4.

To reduce the risk of damage to the cord or plug, pull the plug rather

than the cord when disconnecting the charger from the AC

receptacle.

5.

To reduce the risk of electric shock, unplug the charger from the

outlet before attempting any maintenance or cleaning.

6.

Use of an attachment not recommended or sold by Motorola may

result in a risk of fire, electric shock or personal injury.

7.

Make sure the cord is located so it will not be stepped on, tripped

over or subjected to damage or stress.

8.

An extension cord should not be used unless absolutely necessary.

Use of an improper extension cord could result in a risk of a fire

and/or electric shock. If an extension cord must be used, make sure

that:

•

The pins on the plug of the extension cord are the same number,

size and shape as those on the plug of the charger.

•

The extension cord is properly wired and in good condition.

•

The extension cord size is 18 AWG for lengths up to 100 feet, and

16 AWG for lengths up to 150 feet.

9.

The supply cord of the AC adaptor cannot be replaced. If the cord is

damaged, call customer service at 1-800-638-5119 (U.S. and Canada)

or e-mail us at [email protected].

FCC Licensing Information

Your Motorola radio operates on General Mobile Radio Service (GMRS)

frequencies and is subject to the Rules and Regulations of the Federal

Communications Commission (FCC). The FCC requires that all operators

using GMRS frequencies obtain a radio license before operating their

equipment. To obtain the FCC forms, please visit the FCC’s Web site at

wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159,

which includes all the instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Changes or modifications not expressly approved by Motorola may void

the user’s authority granted by the FCC to operate this radio and should

not be made. To comply with FCC requirements, transmitter adjustments

should be made only by or under the supervision of a person certified as

technically qualified to perform transmitter maintenance and repairs in

the private land mobile and fixed services as certified by an organization

representative of the user of those services. Replacement of any

transmitter component (crystal, semiconductor, etc.) not authorized by

the FCC equipment authorization for this radio could violate FCC rules.

®

Removing the Three AA Alkaline Batteries

1.

Turn the radio off.

2.

With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

3.

Gently remove each alkaline battery by easing each battery out

individually.

4.

Reposition the battery cover and press down to secure.

Notes

•

Exercise care when removing NiMH or AA batteries. Do not use

sharp or conductive tools to remove either of these batteries.

•

Remove the batteries before storing your radio for extended periods

of time. Batteries corrode over time and may cause permanent

damage to your radio.

Using the Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for NiMH

batteries and can be placed on any flat surface, such as a desk or

workbench. Charge the NiMH battery overnight (at least 16 hours) before

using it for the first time. After the initial charge, an empty battery is fully

charged within 14 hours.

1.

Follow the steps above to install a NiMH Battery Pack.

2.

Plug the AC power supply cord into the jack on the desk stand.

3.

Plug the AC power supply into a standard wall outlet.

4.

With a radio facing forward, slide it into one of the charging pockets.

5.

When charging in the battery charger, the red light on the charger

base will glow continuously.

Using the mini-USB Charging Connector

The mini-USB charging connector is a handy port that allows you to

conveniently charge your NiMH battery pack. This is an alternative to

charging your NiMH battery pack in the Battery Charger desk stand

using the AC wall adaptor and especially useful when used while

traveling.

Available mini-USB charging options (Optional Accessories):

1.

Wall travel charger

2.

Vehicle charger

3.

Mini-USB computer cable

If using a computer, the computer must be turned on.

This and other accessories (sold separately) are available for your radio.

For more information, visit our Web site at www.motorola.com or

shop.giantintl.com.

1.

Plug your mini-USB cable or charger into a power source as is

appropriate for your accessory.

2.

Plug the cable into the mini-USB port on the bottom of your radio.

3.

An empty battery will be fully charged in 14 hours.

4.

The LED indicator light on the radio will glow to indicate that the

battery is charging.

Notes

•

The light will remain red after the NiMH battery pack is fully charged.

•

When moving between hot and cold temperatures, do not charge the

NiMH battery pack until the battery temperature acclimates (usually

about 20 minutes).

•

For optimal battery life, remove the radio from the charger within 16

hours. Do not store the radio while connected to the charger.

•

If the radio is kept on while charging, the charging time will be

extended.

•

Even though the charger is connected, you may not be able to

transmit a message if the battery is completely empty

. Allow

time for the battery to charge to 1 bar

before attempting to

transmit a message.

Attaching and Removing the Belt Clip

1.

Attach belt clip to pocket or belt strap.

2.

Align the belt clip post with the hole in the back of the radio.

3.

Gently push until the clip clicks in place.

To Remove

1.

Push down on the release tab at the top of the belt clip to release

the catch.

2.

Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

Turn

clockwise to turn the radio on and counterclockwise to turn the

radio off.

1.

In the ON position, the radio chirps and briefly shows all feature

icons available on the radio.

2.

The display screen then shows the current channel, code and all

features that are enabled.

Setting the Volume

Press and hold

for three seconds while rotating

until you reach a

comfortable listening level.

1.

Rotate

clockwise to increase the volume.

2.

Rotate

counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Talking and Listening

Talking and Listening

To communicate, all radios in your group must be set to the same

channel and Interference Eliminator Code.

1. To talk, press and hold

.

2. When you are finished talking, release

.

For maximum clarity, hold the radio two to three inches away from your

mouth and speak directly into the microphone. Do not cover the

microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet apart.

Power Boost

To boost your radio’s power up to high power, press the top portion of the

button when talking. If you know your party is close by, you can

conserve your battery’s energy by pushing the lower part of the

button to use less power.

Note:

If you are on an FRS only channel (see Channels and Frequencies

table) the radio will only use low power when either portion of the

is pressed.

Monitor Button

Pressing and holding

for three seconds allows you to listen to the

volume level of the radio when you are not receiving. This allows you to

adjust the volume, if necessary. You can also press

to check for

activity on the current channel before you talk.

Push to Talk

Timeout Timer

To prevent accidental transmissions and save battery life, the radio emits

a continuous warning tone and stops transmitting if you press

for 60

continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the radio uses to

transmit. Channels 8-14 are FRS 0.5 watt only and all other channels are

GMRS. (See the "Channels and Frequencies" table on overleaf for details.)

1.

With the radio on, press

. When the radio is on a 0.5

watt channel,

displays. When the radio is on a 1.5 watts

channel,

displays. The current channel flashes.

2.

Press

or

and select an unused or quiet channel.

3.

Press

to save the channel setting or

to continue set up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by blocking

transmissions from unknown sources. Your radio has 121 Interference

Eliminator Codes. Codes 1 – 38 are the standard analog codes that

appear on other FRS/GMRS radios. Codes 39 – 121 are additional digital

codes added for superior interference protection.

0 is the off position, no

analog or digital codes are enabled.

To set the code for a channel:

1.

Press

until the code starts to flash.

2.

Press

or

to select the code.

3.

Press

to save the code setting or

to continue set up.

You can set a different code for each channel using this procedure. An

extended press of

or

allows you to scroll through the Interference

Code rapidly so you can quickly reach the code you want.

Note:

You must set the Interference Eliminator Code to 0 on a radio that

uses Interference Eliminator Codes to communicate with radios that do

not have Interference Eliminator Codes. Select 0 for “no tone, no code”

and OFF will flash on your radio’s display.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in your group

so you can alert them that you want to talk. Your radio has 20 call tones

from which to choose.

To set a call tone:

1.

Press

three times until the current call tone setting flashes and

appears.

2.

Press

or

to change and hear the call tone.

3.

Press

to set the new call tone or

to continue set up.

To transmit your call tone to other radios set to the same channel and

Interference Eliminator Code as your radio, press

.

Note:

Setting the call to 0 disables the call tone feature.

Hands-Free Use Without Accessories (

)

You can use the iVOX feature to transmit hands-free without the need for

any headset accessories. Once iVOX is turned on, the radio detects your

voice and transmits when you speak into the internal microphone.

1.

Press

until

appears on the display. The current setting

On/Off will flash.

2.

Press

or

to select On or Off.

3.

Press

to set or

to continue set up.

Display Screen Guide

Numbers for Channel,

Call Tone

Numbers for Codes

—

Battery Meter

—

Channel Power

Indicator

(see Menu Options)

— Lock

—

Talk Confirmation

Tone (Roger Beep)

—

Noise Filtering

—

On/Off for each

feature

— Scan

— Vibrate

—

Call Tone,

Keypad Tone

—

Weather Alert

—

Hands-Free Use

Without

Accessories

—

Hands-Free Use

With Accessories

Continued on back

MR350/351

Control Buttons

Volume

Push to Talk

(High)

Push to Talk

(Low)

Microphone

Call Tone

Scroll/Weather

Mini-USB

Charging Port

Emergency Alert

LED Indicator

Accessory Jack

Flashlight Button

Scan/Monitor

Menu/Lock

Flashlight LED

Getting Started

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or 3 AA

alkaline batteries and beeps when the batteries are low.

Installing NiMH Rechargeable Battery Pack (Optional Accessory)

1.

Turn the radio off.

2.

With the back of the radio facing you, lift the battery cover latch up

and remove the cover.

3.

Remove the NiMH battery pack from the clear plastic bag (do not

disassemble or unwrap the battery pack).

4.

Insert the NiMH battery pack with the diagram facing you. (The

ribbon should be underneath the battery pack and should wrap

around the right side of the pack for easy removal.)

5.


Installing the Three AA Alkaline Batteries

1.

Turn the radio off.

2.

With the back of the radio facing you, lift the battery cover latch up

and remove the cover.

3.

Insert the three AA alkaline batteries with + and - polarity as shown

inside. (The ribbon should be underneath the AA alkaline batteries

and should wrap around the right side of the batteries.)

4.


Radio Battery Meter

The radio battery icon shows the battery charge level, from full

to

empty

. When the radio has one segment left, the

radio chirps periodically or after releasing

(Low Battery Alert).

Removing the NiMH Battery Pack (Optional Accessory)

1.

Turn the radio off.

2.

With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

3.

Remove the NiMH battery pack by pulling the ribbon attached to

the radio.

4.


For a fax:

Contact the

Fax-0n-Demand

system

For mail service:

Call the FCC

Forms Hotline

If you have

questions about

the FCC License:

Call the FCC

1-202-418-0177

1-800-418-FORM

(3676)

1-888-CALL-FCC

(225-5322)

Two-Way Radio

User’s Guide

Motorola MR350R User Guide - Page 1

Motorola MR350R - Range FRS/GMRS Radio Manual

Page 1 highlights