Mr. Coffee BVMC-BMH23 User Manual - Page 6

11. C lean after every third use for best performance. 12. A fter using, open the grinder to the coarsest setting and run empty to clear the grinding path. NOTE: F or optimum freshness of your coffee beans, do NOT store in the bean hopper for extended periods of time. CLEANING INSTRUCTIONS Remember to always clean your Burr Mill before using it for the first time. Then, to ensure optimal mill function and durability, clean it regularly following these simple steps: 1. Always unplug your Burr Mill after use and before cleaning. 2. Wash the bean hopper and coffee chamber parts with warm soapy water. (Never use abrasive cleansers, steel wool pads or other abrasive materials. UNIT IS NOT DISHWASHER SAFE) CAUTION! Never immerse the Burr Mill itself in water, in any other liquid or place in the dishwasher. 3. Dry all pieces thoroughly. 4. Install the Bean Hopper onto the unit and turn clockwise (several rotations-will hear clicking as unit gets tighter) until it stops with the grind size indicator on Fine. 5. Place chamber lid back on grinder chamber and then install into unit, tightly locking into place. NOTE: If all Bean Hopper and Grinding Chamber parts are not tightly in place correctly, the safety switches within the machine will not allow the grinder to work. You MUST have all parts in place to safely use the Burr Mill. TROUBLESHOOTING YOUR MR. COFFEE® Burr Mill Your MR. COFFEE® Burr Mill has been carefully designed to give you many years of trouble-free service. In the unlikely event that your new Burr Mill does not operate satisfactorily, please review the following potential problems and try the steps recommended BEFORE you call an Authorized Sunbeam Service Center. PROBLEM POSSIBLE CAUSE SOLUTION THE UNIT DOES NOT GRIND • Hopper is not securely intact • Hopper lid is not on tight • Ground coffee chamber is not in position • Start button has not been pressed • Unit is unplugged • There's a power outage • Motor has overheated, thermal fuse is open • Hopper Chute Clogged (or Blocked) • TURN HOPPER CLOCKWISE UNTIL STOPS, THEN MOVE INDICATOR COUNTERCLOCKWISE, BACK TILL YOU HAVE INDICATOR LINED UP WITH DESIRED GRIND SETTING • SECURE HOPPER LID • PLACE CHAMBER IN PROPER POSITION • P RESS AND HOLD BRIEFLY START/STOP BUTTON • PLUG UNIT IN • WAIT FOR POWER TO BE RESTORED • unplug unit for at least an hour then plug back in and use as needed • Remove Hopper & Empty to Clear Blockage 10 Troubleshooting cont. THE COFFEE GROUNDS PRODUCED ARE INSUFFICIENT THE SIZE OF GROUND COFFEE PARTICLES IS NOT CONSISTENT THE UNIT STOPS GRINDING • Grinder setting is incorrect • Insufficient amount of whole beans in hopper • Ground coffee chamber moved out of position during operation • Top Burr Mill is not in proper position • Unit and Burr Mill are not clean • There is a foreign object between the two Burr Mills • Unit and Burr Mill are not clean • T here's a foreign object between the two Burr Mills • Grind setting is not correct • SET Grinder setting CORRECTLY • ADD BEANS TO HOPPER • PLACE CHAMBER IN PROPER POSITION • UNPLUG UNIT, PLACE TOP Burr Mill IN PROPER POSITION • CLEAN UNIT, UNPLUG IT AND CLEAN Burr Mill • UNPLUG UNIT AND CAREFULLY DISLODGE FOREIGN OBJECT • CLEAN UNIT, UNPLUG IT AND CLEAN Burr Mill • UNPLUG UNIT AND CAREFULLY DISLODGE FOREIGN OBJECT • T URN HOPPER TO CORRECT GRIND SETTING • Grind setting is incorrect • Ground coffee chamber is not in correct position • Start/Stop button has been pressed • The unit has been unplugged • There's a power outage • Ground coffee chamber is full and is clogging the Burr Mill compartment • SET GRIND SETTING CORRECTLY • PLACE CHAMBER IN PROPER POSITION • P RESS AND HOLD BRIEFLY START/STOP BUTTON again • PLUG UNIT IN • WAIT FOR POWER TO BE RESTORED • REMOVE CHAMBER, EMPTY AND REPLACE; UNPLUG UNIT AND CLEAN Burr Mill COMPARTMENT IF NEEDED THE CUP SELECTION DIAL DOES NOT TURN • Motor has overheated, thermal fuse is open • unplug unit for at least an hour then plug back in and use as needed • Timer is at 2 cup setting, cannot turn counterclockwise anymore • Timer is at 18 cup setting, cannot turn clockwise anymore • Cup selection dial is broken • TURN CLOCKWISE TO SET DESIRED NUMBER OF CUPS • TURN counter CLOCKWISE TO SET DESIRED NUMBER OF CUPS • call MR. COFFEE® Consumer Service Department number below THE GRIND SETTING hopper DOES NOT TURN • Hopper is at the Fine Setting, cannot turn clockwise anymore • Unit and Burr Mill are not clean • There's a foreign object between the two Burr Mills • TURN COUNTERCLOCKWISE FOR DESIRED GRIND SETTING • CLEAN UNIT, UNPLUG IT AND CLEAN Burr Mill • UNPLUG UNIT AND CAREFULLY DISLODGE FOREIGN OBJECT Do you still have questions? You can call us toll-free at the MR. COFFEE® Consumer Service Department 1-800-MR. COFFEE® (1-800-672-6333) or you can visit us at www.mrcoffee.com 11