NEC ASLCD92VXM-BK AccuSync LCD72VXM_92VXM - Page 5

Quick Start

Get NEC ASLCD92VXM-BK - AccuSync - 19inch LCD Monitor PDF manuals and user guides
UPC - 805736015942
View all NEC ASLCD92VXM-BK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Quick Start To attach the Base to the LCD Stand: 1. Insert the front of the LCD Stand into the holes in the front of the Base (Figure 1). 2. Next, position the locking tabs on the back side of the LCD Stand with the holes on the Base. Lower the Stand until locking tabs are secure. 3. Attach the clip into the base (Figure 2). Figure 1 Figure 2 Stand Locking Tabs Front Base To attach the AccuSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.2). Tighten all screws. For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure A.3). Tighten all screws. NOTE: To obtain the AccuSync Macintosh cable adapter, call NEC Display Solutions of America, Inc. at (800) 632-4662. 3. Connect the15-pin mini D-SUB cable to the appropriate connector on the back of the monitor. (Figure B.1) Connect one end of the audio cable to AUDIO-INPUT on the back of the monitor and the other end to the "Audio Out" terminal on the computer. Headphones may connected to the "Headphones" output, " ", on the front of the monitor. While headphones are connected, the sound from the speakers will be disabled. 4. Connect one end of the power cord to the LCD and the other end to the power outlet. Place the video signal cable, power cord, DVI cable, and audio cable into the cable holder (Figure B.1). NOTE: Adjust the position of cables in the holder to avoid damage. NOTE: Refer to Recommended Use section of this manual for proper selection of power cord. 5. Turn on the monitor with the front power button and then turn on computer. (Figure C.1) 6. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings. For further adjustments, use the following OSM® controls: • Auto Adjust Contrast • Auto Adjust Refer to the Controls section of this User's Manual for a full description of these OSM controls. NOTE: For download information on the Windows® 95/98/Me/2000/XP INF file for your AccuSync monitor, refer to the References section of this User's Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
3
Quick Start
To attach the Base to the LCD Stand:
±. Insert the front of the LCD Stand into the holes in the front of the Base (Figure ±).
2. Next, position the locking tabs on the back side of the LCD Stand with the holes on the
Base. Lower the Stand until locking tabs are secure.
3. Attach the clip into the base (Figure 2).
Stand
Figure ±
Figure 2
To attach the AccuSync LCD monitor to your system, follow these instructions:
±. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the
connector of the display card in your system
(Figure A.1)
. Tighten all screws.
For the PC with Analog output: Connect the ±5-pin mini D-SUB signal cable to the connector of
the display card in your system
(Figure A.2)
. Tighten all screws.
For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the
±5-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter
(Figure A.3)
. Tighten
all screws.
NOTE:
To obtain the AccuSync Macintosh cable adapter, call NEC Display Solutions
of America, Inc. at (800) 632-4662.
3. Connect the±5-pin mini D-SUB cable to the appropriate connector on the back of the monitor.
(Figure B.1)
Connect one end of the audio cable to AUDIO-INPUT on the back of the monitor and
the other end to the “Audio Out” terminal on the computer. Headphones may connected to the
“Headphones” output, “
”, on the front of the monitor. While headphones are connected, the
sound from the speakers will be disabled.
4. Connect one end of the power cord to the LCD and the other end to the power outlet. Place the
video signal cable, power cord, DVI cable, and audio cable into the cable holder
(Figure B.1)
.
NOTE:
Adjust the position of cables in the holder to avoid damage.
NOTE: Refer to Recommended Use section of this manual for proper selection of power cord.
5. Turn on the monitor with the front power button and then turn on computer.
(Figure C.1)
6. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for
most timings. For further adjustments, use the following OSM
®
controls:
• Auto Adjust Contrast
• Auto Adjust
Refer to the Controls section of this User’s Manual for a full description of these OSM controls.
NOTE: For download information on the Windows
®
95/98/Me/2000/XP INF file for your
AccuSync monitor, refer to the References section of this User’s Manual.
NOTE: If you have any problems, please refer to the Troubleshooting section of this
User’s Manual.
Front Base
Locking Tabs