NEC E231W-BK E231W-BK : user's manual - Page 8

Quick Start - monitor

Get NEC E231W-BK PDF manuals and user guides
UPC - 805736034707
View all NEC E231W-BK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 2. Please pivot base 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand. 3. Attach the base stand to LCD monitor and lock screws of base stand bottom (Figure 2). NOTE: Reverse this procedure if you need to re-pack the monitor. To attach the MultiSync LCD monitor to your system, follow these instructions: Control Figure 1 buttons Screws 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.2). Tighten all screws. For the MAC: Connect the Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the Macintosh cable adapter (Figure A.3). Tighten all screws. Figure 2 For the PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system (Figure A.4). DVI signal cable Figure A.1 Macintosh Figure A.2 Cable Adapter (not included) Figure A.3 NOTE: Some Macintosh systems do not require a Macintosh cable adapter. DisplayPort cable (not included) Figure A.4 3. Place hands on each side of the monitor to tilt the LCD panel 20-degree angle and lift up to the highest position (FigureB.1). 4. Connect all cables to the appropriate connector on the back of the monitor (Figure B.1). 5. Position the Video Signal Cable and power cord between the holes on the Stand, as indicated in Figure B.2/Figure B.3. 20˚ Tilt Highest stand position Power Cord DisplayPort DVI D-SUB Figure B.1 Figure B.2 NOTE: 1. Please use a DisplayPort cable with a DisplayPort logo. 2. The DisplayPort connector does not supply power to the connected component. 3. When removing the DisplayPort cable, hold down the top button to release the lock. English-6 Figure B.3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
English-6
Quick Start
To attach the Base to the LCD stand:
1.
Place monitor face down on a non-abrasive surface (
Figure 1
).
NOTE:
Handle with care when monitor facing down, for avoiding damage to the front
control buttons.
2.
Please pivot base 90 degrees as shown in
Figure 1
.
NOTE:
Handle with care when pulling the stand.
3.
Attach the base stand to LCD monitor and lock screws of base stand bottom (
Figure 2
).
NOTE:
Reverse this procedure if you need to re-pack the monitor.
To attach the MultiSync LCD monitor to your system, follow these instructions:
1.
Turn off the power to your computer.
2.
For the PC or MAC with DVI digital output:
Connect the DVI signal cable to the
connector of the display card in your system (
Figure A.1
). Tighten all screws.
For the PC with Analog output:
Connect the 15-pin mini D-SUB signal cable to the
connector of the display card in your system (
Figure A.2
). Tighten all screws.
For the MAC:
Connect the Macintosh cable adapter to the computer, then attach the
15-pin mini D-SUB signal cable to the Macintosh cable adapter (
Figure A.3
).
Tighten all screws.
For the PC with DisplayPort output:
Connect the DisplayPort cable to the connector of the display card in your system
(
Figure A.4
).
Figure 2
Screws
Figure 1
Control
buttons
NOTE:
Some Macintosh systems do not require a Macintosh cable adapter.
3.
Place hands on each side of the monitor to tilt the LCD panel 20-degree angle and lift up to the highest position
(
FigureB.1
).
4.
Connect all cables to the appropriate connector on the back of the monitor (
Figure B.1
).
5.
Position the Video Signal Cable and power cord between the holes on the Stand, as indicated in
Figure B.2
/
Figure B.3
.
Power Cord
D-SUB
Figure B.1
Figure B.2
Figure B.3
Highest stand position
20˚ Tilt
DVI
DisplayPort
NOTE:
1.
Please use a DisplayPort cable with a DisplayPort logo.
2.
The DisplayPort connector does not supply power to the connected component.
3.
When removing the DisplayPort cable, hold down the top button to release the lock.
Figure A.1
Figure A.3
Macintosh
Cable Adapter
(not included)
Figure A.2
DVI signal cable
Figure A.4
DisplayPort cable
(not included)