NEC LCD175VX LCD175VX/195VX user's manual - Page 5

Quick Start - auto adjust

Get NEC LCD175VX - MultiSync - 17inch LCD Monitor PDF manuals and user guides
UPC - 805736017748
View all NEC LCD175VX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Quick Start To attach the Base to the LCD Stand: 1. Insert the front of the LCD Stand into the holes in the front of the Base (Figure 1). 2. Next, position the locking tab on the back side of the LCD Stand with the hole on the Base. Lower the Stand until locking tabs are secure. 3. Attach the clip into the base (Figure 2). Figure 1 Figure 2 Stand Locking Tab Front Base To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.2). Tighten all screws. For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure A.3). Tighten all screws. NOTE: To obtain the MultiSync Macintosh cable adapter, call NEC Display Solutions of America, Inc. at (800) 632-4662. 3. Connect the cables to the appropriate connector on the back of the monitor (Figure B.1) NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 4. Connect one end of the power cord to the LCD and the other end to the power outlet. Place the video signal cable, power cord and DVI cable into the cable holder (Figure B.1). NOTE: Adjust the position of cables in the cable holder to avoid damage. NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 5. Turn on the monitor with the front power button and the computer. (Figure C.1) 6. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings. For further adjustments, use the following OSM® controls: • Auto Adjust Contrast • Auto Adjust Refer to the Controls section of this User's Manual for a full description of these OSM controls. NOTE: For download information on the Windows® 95/98/Me/2000/XP INF file for your MultiSync monitor, refer to the References section of this User's Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
3
Quick Start
To attach the Base to the LCD Stand:
±. Insert the front of the LCD Stand into the holes in the front of the Base
(Figure 1)
.
2. Next, position the locking tab on the back side of the LCD Stand with the hole on the
Base. Lower the Stand until locking tabs are secure.
3. Attach the clip into the base
(Figure 2)
.
Locking Tab
Front Base
Stand
Figure ±
Figure 2
To attach the MultiSync LCD monitor to your system, follow these instructions:
±. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the
connector of the display card in your system (
Figure A.1
). Tighten all screws.
For the PC with Analog output: Connect the ±5-pin mini D-SUB signal cable to the connector
of the display card in your system
(Figure A.2)
. Tighten all screws.
For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach
the ±5-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter
(Figure A.3)
.
Tighten all screws.
NOTE: To obtain the MultiSync Macintosh cable adapter, call
NEC Display Solutions of America, Inc. at (800) 632-4662.
3. Connect the cables to the appropriate connector on the back of the monitor
(Figure B.1)
NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use
section of this manual for proper selection of power cord.
4. Connect one end of the power cord to the LCD and the other end to the power outlet. Place the
video signal cable, power cord and DVI cable into the cable holder
(Figure B.1)
.
NOTE: Adjust the position of cables in the cable holder to avoid damage.
NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use
section of this manual for proper selection of power cord.
5. Turn on the monitor with the front power button and the computer.
(Figure C.1)
6. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial
setup for most timings. For further adjustments, use the following OSM
®
controls:
• Auto Adjust Contrast
• Auto Adjust
Refer to the Controls section of this User’s Manual for a full description of these
OSM controls.
NOTE:
For download information on the Windows
®
95/98/Me/2000/XP INF file for
your MultiSync monitor, refer to the
References
section of this User’s Manual.
NOTE:
If you have any problems, please refer to the
Troubleshooting
section of this
User’s Manual.