NEC LCDMT840 User Manual - Page 16

When using a Macintosh with the projector, set the DIP switches of the supplied pin adapter according to your resolution. After setting, restart your Macintosh. See the following pages for setting of the DIP switches. • When using with a Macintosh, SVGA(800‫ן‬600 :MT840)/ XGA(1024‫ן‬768 : MT1040/MT1045) is recommended if your Macintosh supports this mode. • When using with a Macintosh PowerBook, output may not be set to 800‫ן‬600 unless "mirroring" is off on your PowerBook. Refer to owner's manual supplied with your Macintosh computer for mirroring. NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub 15-pin connector. Settings for Monitor Mode Number of DIP switch Resolution 1 13" multi-scan mode /16"-13" ON 17" multi-scan mode /19"-13" ON 21" multi-scan mode /21"-13" ON 13" fixed mode /640x480 ON VGA/SVGA mode 16" fixed mode /832x624 19" fixed mode /1024x768 21" fixed mode /1152x870 ON 23 ON ON ON ON ON ON ON ON ON ON 456 ON ON ON ON ON ON ON NOTE: For settings other than display modes supported by your Macintosh and the projector, use of the DIP switch may bounce an image slightly or may display nothing. If this happens, set the DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then restart the Macintosh again. Make sure that the projector and your Macintosh are connected with the pin adapter and the supplied signal cable (mini DSub 15-pin connector) and then restart your Macintosh. Examples of DIP switch setting 17" multi-scan mode VGA/SVGA mode ON ON 19" fixed mode ON 1 2 34 5 6 1 2 34 5 6 1 2 34 5 6 NOTE: Refer to your computer's owner's manual for more information about your computer's video output requirements and any special identification or configuring your projector's image and monitor may require. Connecting Your DVD Player You can connect your projector to a DVD player with component outputs or Video output. To do so, simply: 1. Turn off the power to your projector and DVD player. 2. If your DVD player has the component video (Y,Cb,Cr) output, use the optional 15-pin-to-RCA x 3 cable to connect your DVD player to the RGB INPUT connector on the projector. For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite VIDEO output of the DVD player to the Video Input of the projector. 3. Turn on the projector and the DVD player. NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements. Connecting Your VCR Or Laser Disc Player Use common RCA cables (not provided) to connect your VCR or laser disc player to your projector. To make these connections, simply: 1. Turn off the power to the projector and VCR or laser disc player. 2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your projector. Use standard RCA audio patch cords to connect the audio from your VCR or laser disc player to the projector (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound. 3. Turn on the projector and the VCR or laser disc player. NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements. ConnectingYour Computer to the Mouse Output Port The built-in remote mouse receiver enables you to operate your computer's mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations. To connect the mouse output port: 1. Turn off your computer. 2. For PCs: Remove your current mouse and connect the supplied serial cable from the mouse output to your PC's mouse port. (Use the 6-pin adapter for connecting to a PS/2 computer.) For Macintosh: Remove your current mouse from your computer, attach the Macintosh adapter to the mouse output port's serial cable, and connect the projector to your mouse port. 3. When the built-in remote mouse receiver is available, it will disable your regular mouse, disconnect the serial cable and restart your computer. MOUSE PC CONTROL OUT REMOTE CONTROL INPUT AUDIO RGB INPUT 1 AUDIO RGB INPUT 2 S-VIDEO L/MONO R VIDEO IBM PC/AT Serial cable (Supplied) PC CONTROL MOUSE OUT REMOTE CONTROL INPUT AUDIO RGB INPUT 1 AUDIO RGB INPUT 2 S-VIDEO L/MONO R VIDEO Macintosh IBM PS2 Serial cable (Supplied) NOTE:Some computers or software programs may not work with the MOUSE OUT port. E-16