NEC LT150Z User Manual - Page 30

Operation

Get NEC LT150Z - MultiSync XGA DLP Projector PDF manuals and user guides View all NEC LT150Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

3.OPERATION Connecting the Power Cable and Turn on the Projector Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. 1 Connect the supplied power cable to the projector. STATUPOSWER ONS/TAND BY SOURCE MENU SELECT ENTER PC CAAURATDDOJAUCSCTESS PC CARD AUDIO S-VIDEO RGB PC CONTROL VIDEO USB AC IN To turn off the projector: First press the "POWER" button on the projector cabinet or the remote control for a minimum of two seconds. The power indicator will glow orange. After the projector turns off, the cooling fans keep operating for 90 seconds. NOTE: Do not disconnect the power cable during this time. Then, unplug the power cable. The power indicator will go out. Status of indicator light: turn on stand by STATUS POWER ON/STAND BY steady orange light flashing 3 to 5 minutes STATUS POWER steady light STATUS POWER ME CEL CANCEL ME CEL ENTER ENT ENT Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange. 2 Turn on and off the Projector SOURCE AUTO ADJ. NU Vol. SELECT Vol. ER CAN MAGNIFY POINTER PIC. MUTE HELP POWER POWER ON/STAND BY button POWSETRATUS Indicator STOANND/ BY SOURCE RGB Power button RD-366E To turn on the projector: Only after you press the "POWER" button on the projector cabinet or the remote control will the power indicator turn to green and the projector become ready to use. NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. (See page E-42.) NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized. flashing green light steady green light Status of indicator light: turn off ON STATUS POWER steady green light ON/STAND BY press a minimum of two seconds cooling down STATUS POWER stand by STATUS POWER change to flashing green light steady orange light 3 Adjust a Projected Image Select the Computer or Video Source SOURCE AUTO ADJ. NU Vol. SELECT Vol. ER CAN POINTER PIC. MUTE OANND/ BY SOURCE PC CARD ACCESSADAJUUSTOT E-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
E–27
RGB
STATUS
POWER
ON/
STAND BY
SOURCE
3.OPERATION
AC IN
PC CARD
USB
VIDEO
S-VIDEO
RGB
AUDIO
PC CONTROL
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
AUTO
ADJUST
PC CARD ACCESS
STATUS
POWER
ON/
STAND BY
SOURCE
1
Connect the supplied power cable to the projector.
2
Turn on and off the Projector
3
Connecting the Power Cable and Turn on the Projector
POWER ON/STAND BY button
Indicator
To turn on the projector:
Only after you press the “POWER” button on the projector
cabinet or the remote control will the power indicator turn to
green and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable, use
the menu and enable the “Auto Start” feature. (See page E-42.)
NOTE: Immediately after turning on the projector, screen flicker may
occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting
is stabilized.
Power button
To turn off the projector:
First press the “POWER” button on the projector cabinet or
the remote control for a minimum of two seconds. The power
indicator will glow orange. After the projector turns off, the
cooling fans keep operating for 90 seconds.
NOTE: Do not disconnect the power cable during this time. Then,
unplug the power cable. The power indicator will go out.
SELECT
Vol.
Vol.
POINTER
POWER
HELP
RD-366E
PIC.
MUTE
MAGNIFY
SOURCE
AUTO
ADJ.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
POWER
STATUS
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
POWER
STATUS
Status of indicator light: turn on
stand by
flashing 3 to 5 minutes
steady light
Status of indicator light: turn off
steady orange light
flashing green light
steady green light
ON
cooling down
stand by
steady green light
change to flashing
green light
steady orange light
press a minimum of
two seconds
SELECT
Vol.
Vol.
POINTER
PIC.
MUTE
SOURCE
AUTO
ADJ.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
E
N
T
E
R
AUTO
ADJUST
PC CARD ACCESS
ON/
AND BY
SOURCE
Select the Computer or Video Source
Adjust a Projected Image
Plug the supplied power cable in the wall outlet. The projec-
tor will go into its standby mode and the power indicator will
glow orange.
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.