NEC NP-V300W RS232 codes- Projectors - Page 5

NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps - model

Get NEC NP-V300W PDF manuals and user guides View all NEC NP-V300W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode". The projector cannot use the control commands in the power-saving condition, but the following model can use some control commands. [P350X/P350W/P420X Series] STANDBY MODE: "POWER-SAVING" Control Command POWER ON Yes: Supported No: Not supported Serial Wired Wireless port LAN port LAN unit Yes No No [PA600X/PA550W/PA500U/PA500X Series] STANDBY MODE: "POWER-SAVING" Control Command POWER ON Serial Wired Wireless port LAN port LAN unit Yes No No [PA600X/PA550W/PA500U/PA500X Series] STANDBY MODE: "NETWORK STANDBY" Serial Control Command port POWER ON Yes Yes: Supported No: Not supported Wired LAN port Yes Wireless LAN unit Yes Baud rate: Data length: Parity bit: Stop bits: Communications mode: 38400 bps (NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps) 8 bits No parity 1 bit Full duplex The control connector is described below. [ HT/LT/NP40/VT70/VT80/VT90/WT ] The PC CONTROL connector is a mini DIN 8-pin connector. 1 To TxD of PC 2 3 4 To GND of PC 5 6 7 To RxD of PC 8 * 2, 3, 5, 6, and 8 are used inside the projector. [ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode".
The projector cannot use the control commands in the power-saving condition, but the following model can use
some control commands.
[P350X/P350W/P420X Series]
STANDBY MODE: "POWER-SAVING"
Control Command
Serial
port
Wired
LAN port
Wireless
LAN unit
POWER ON
Yes
No
No
Yes:
Supported
No: Not supported
[PA600X/PA550W/PA500U/PA500X Series]
STANDBY MODE: "POWER-SAVING"
Control Command
Serial
port
Wired
LAN port
Wireless
LAN unit
POWER ON
Yes
No
No
[PA600X/PA550W/PA500U/PA500X Series]
STANDBY MODE: "NETWORK STANDBY"
Control Command
Serial
port
Wired
LAN port
Wireless
LAN unit
POWER ON
Yes
Yes
Yes
Yes:
Supported
No: Not supported
Baud rate:
38400 bps
(NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps)
Data length:
8 bits
Parity bit:
No parity
Stop bits:
1 bit
Communications mode:
Full duplex
The control connector is described below.
[ HT/LT/NP40/VT70/VT80/VT90/WT ]
The PC CONTROL connector is a mini DIN 8-pin connector.
1
To TxD of PC
2
3
4
To GND of PC
5
6
7
To RxD of PC
8
* 2, 3, 5, 6, and 8 are used inside the projector.
[ GT/LT80/MT/NP1000/VT (except
VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ]